441 lines
14 KiB
Rust
441 lines
14 KiB
Rust
use crate::config::PlantControllerConfig;
|
|
use crate::hal::battery::BatteryInteraction;
|
|
use crate::hal::esp::Esp;
|
|
use crate::hal::rtc::RTCModuleInteraction;
|
|
use crate::hal::v4_sensor::SensorImpl;
|
|
use crate::hal::v4_sensor::SensorInteraction;
|
|
use crate::hal::water::TankSensor;
|
|
use crate::hal::{
|
|
deep_sleep, BoardInteraction, FreePeripherals, Sensor, I2C_DRIVER, PLANT_COUNT
|
|
};
|
|
use crate::log::{log, LogMessage};
|
|
use anyhow::bail;
|
|
use embedded_hal::digital::OutputPin;
|
|
use embedded_hal_bus::i2c::MutexDevice;
|
|
use ina219::address::{Address, Pin};
|
|
use ina219::calibration::UnCalibrated;
|
|
use ina219::configuration::{Configuration, OperatingMode};
|
|
use ina219::SyncIna219;
|
|
use measurements::{Current, Resistance, Voltage};
|
|
use pca9535::{GPIOBank, Pca9535Immediate, StandardExpanderInterface};
|
|
use std::result::Result::Ok as OkStd;
|
|
use embedded_can::Frame;
|
|
use embedded_can::StandardId;
|
|
use alloc::string::ToString;
|
|
use alloc::boxed::Box;
|
|
use esp_hal::gpio::Pull;
|
|
|
|
pub enum Charger<'a> {
|
|
SolarMpptV1 {
|
|
mppt_ina: SyncIna219<MutexDevice<'a, I2cDriver<'a>>, UnCalibrated>,
|
|
solar_is_day: PinDriver<'a, esp_idf_hal::gpio::AnyIOPin, esp_idf_hal::gpio::Input>,
|
|
charge_indicator: PinDriver<'a, esp_idf_hal::gpio::AnyIOPin, InputOutput>,
|
|
},
|
|
ErrorInit {},
|
|
}
|
|
|
|
impl Charger<'_> {
|
|
pub(crate) fn power_save(&mut self) {
|
|
match self {
|
|
Charger::SolarMpptV1 { mppt_ina, .. } => {
|
|
let _ = mppt_ina
|
|
.set_configuration(Configuration {
|
|
reset: Default::default(),
|
|
bus_voltage_range: Default::default(),
|
|
shunt_voltage_range: Default::default(),
|
|
bus_resolution: Default::default(),
|
|
shunt_resolution: Default::default(),
|
|
operating_mode: OperatingMode::PowerDown,
|
|
})
|
|
.map_err(|e| {
|
|
log::info!(
|
|
"Error setting ina mppt configuration during deep sleep preparation{:?}",
|
|
e
|
|
);
|
|
});
|
|
}
|
|
_ => {}
|
|
}
|
|
}
|
|
fn set_charge_indicator(&mut self, charging: bool) -> anyhow::Result<()> {
|
|
match self {
|
|
Self::SolarMpptV1 {
|
|
charge_indicator, ..
|
|
} => {
|
|
charge_indicator.set_state(charging.into())?;
|
|
}
|
|
_ => {}
|
|
}
|
|
Ok(())
|
|
}
|
|
|
|
fn is_day(&self) -> bool {
|
|
match self {
|
|
Charger::SolarMpptV1 { solar_is_day, .. } => solar_is_day.get_level().into(),
|
|
_ => true,
|
|
}
|
|
}
|
|
|
|
fn get_mptt_voltage(&mut self) -> anyhow::Result<Voltage> {
|
|
let voltage = match self {
|
|
Charger::SolarMpptV1 { mppt_ina, .. } => mppt_ina
|
|
.bus_voltage()
|
|
.map(|v| Voltage::from_millivolts(v.voltage_mv() as f64))?,
|
|
_ => {
|
|
bail!("hardware error during init")
|
|
}
|
|
};
|
|
Ok(voltage)
|
|
}
|
|
|
|
fn get_mptt_current(&mut self) -> anyhow::Result<Current> {
|
|
let current = match self {
|
|
Charger::SolarMpptV1 { mppt_ina, .. } => mppt_ina.shunt_voltage().map(|v| {
|
|
let shunt_voltage = Voltage::from_microvolts(v.shunt_voltage_uv().abs() as f64);
|
|
let shut_value = Resistance::from_ohms(0.05_f64);
|
|
let current = shunt_voltage.as_volts() / shut_value.as_ohms();
|
|
Current::from_amperes(current)
|
|
})?,
|
|
_ => {
|
|
bail!("hardware error during init")
|
|
}
|
|
};
|
|
Ok(current)
|
|
}
|
|
}
|
|
|
|
pub struct V4<'a> {
|
|
esp: Esp<'a>,
|
|
tank_sensor: TankSensor<'a>,
|
|
charger: Charger<'a>,
|
|
rtc_module: Box<dyn RTCModuleInteraction + Send>,
|
|
battery_monitor: Box<dyn BatteryInteraction + Send>,
|
|
config: PlantControllerConfig,
|
|
|
|
awake: PinDriver<'a, esp_idf_hal::gpio::AnyIOPin, Output>,
|
|
light: PinDriver<'a, esp_idf_hal::gpio::AnyIOPin, InputOutput>,
|
|
general_fault: PinDriver<'a, esp_idf_hal::gpio::AnyIOPin, InputOutput>,
|
|
pump_expander: Pca9535Immediate<MutexDevice<'a, I2cDriver<'a>>>,
|
|
pump_ina: Option<SyncIna219<MutexDevice<'a, I2cDriver<'a>>, UnCalibrated>>,
|
|
sensor: SensorImpl<'a>,
|
|
extra1: PinDriver<'a, esp_idf_hal::gpio::AnyIOPin, Output>,
|
|
extra2: PinDriver<'a, esp_idf_hal::gpio::AnyIOPin, Output>,
|
|
}
|
|
|
|
pub(crate) fn create_v4(
|
|
peripherals: FreePeripherals,
|
|
esp: Esp<'static>,
|
|
config: PlantControllerConfig,
|
|
battery_monitor: Box<dyn BatteryInteraction + Send>,
|
|
rtc_module: Box<dyn RTCModuleInteraction + Send>,
|
|
) -> anyhow::Result<Box<dyn BoardInteraction<'static> + Send + 'static>> {
|
|
log::info!("Start v4");
|
|
let mut awake = PinDriver::output(peripherals.gpio21.downgrade())?;
|
|
awake.set_high()?;
|
|
|
|
let mut general_fault = PinDriver::input_output(peripherals.gpio23.downgrade())?;
|
|
general_fault.set_pull(Pull::Floating)?;
|
|
general_fault.set_low()?;
|
|
|
|
let mut extra1 = PinDriver::output(peripherals.gpio6.downgrade())?;
|
|
extra1.set_low()?;
|
|
|
|
let mut extra2 = PinDriver::output(peripherals.gpio15.downgrade())?;
|
|
extra2.set_low()?;
|
|
|
|
let one_wire_pin = peripherals.gpio18.downgrade();
|
|
let tank_power_pin = peripherals.gpio11.downgrade();
|
|
let flow_sensor_pin = peripherals.gpio4.downgrade();
|
|
|
|
let tank_sensor = TankSensor::create(
|
|
one_wire_pin,
|
|
peripherals.adc1,
|
|
peripherals.gpio5,
|
|
tank_power_pin,
|
|
flow_sensor_pin,
|
|
peripherals.pcnt1,
|
|
)?;
|
|
|
|
let mut sensor_expander = Pca9535Immediate::new(MutexDevice::new(&I2C_DRIVER), 34);
|
|
let sensor = match sensor_expander.pin_into_output(GPIOBank::Bank0, 0) {
|
|
Ok(_) => {
|
|
log::info!("SensorExpander answered");
|
|
//pulse counter version
|
|
let mut signal_counter = PcntDriver::new(
|
|
peripherals.pcnt0,
|
|
Some(peripherals.gpio22),
|
|
Option::<AnyInputPin>::None,
|
|
Option::<AnyInputPin>::None,
|
|
Option::<AnyInputPin>::None,
|
|
)?;
|
|
|
|
signal_counter.channel_config(
|
|
PcntChannel::Channel0,
|
|
PinIndex::Pin0,
|
|
PinIndex::Pin1,
|
|
&PcntChannelConfig {
|
|
lctrl_mode: PcntControlMode::Keep,
|
|
hctrl_mode: PcntControlMode::Keep,
|
|
pos_mode: PcntCountMode::Increment,
|
|
neg_mode: PcntCountMode::Hold,
|
|
counter_h_lim: i16::MAX,
|
|
counter_l_lim: 0,
|
|
},
|
|
)?;
|
|
|
|
for pin in 0..8 {
|
|
let _ = sensor_expander.pin_into_output(GPIOBank::Bank0, pin);
|
|
let _ = sensor_expander.pin_into_output(GPIOBank::Bank1, pin);
|
|
let _ = sensor_expander.pin_set_low(GPIOBank::Bank0, pin);
|
|
let _ = sensor_expander.pin_set_low(GPIOBank::Bank1, pin);
|
|
}
|
|
|
|
SensorImpl::PulseCounter {
|
|
signal_counter,
|
|
sensor_expander,
|
|
}
|
|
}
|
|
Err(_) => {
|
|
log::info!("Can bus mode ");
|
|
let timing = can::config::Timing::B25K;
|
|
let config = can::config::Config::new().timing(timing);
|
|
let can = can::CanDriver::new(peripherals.can, peripherals.gpio0, peripherals.gpio2, &config).unwrap();
|
|
|
|
|
|
let frame = StandardId::new(0x042).unwrap();
|
|
let tx_frame = Frame::new(frame, &[0, 1, 2, 3, 4, 5, 6, 7]).unwrap();
|
|
can.transmit(&tx_frame, 1000).unwrap();
|
|
|
|
if let Ok(rx_frame) = can.receive(1000) {
|
|
log::info!("rx {:}:", rx_frame);
|
|
}
|
|
//can bus version
|
|
SensorImpl::CanBus {
|
|
can
|
|
}
|
|
}
|
|
};
|
|
|
|
|
|
|
|
|
|
let mut solar_is_day = PinDriver::input(peripherals.gpio7.downgrade())?;
|
|
solar_is_day.set_pull(Pull::Floating)?;
|
|
|
|
let mut light = PinDriver::input_output(peripherals.gpio10.downgrade())?;
|
|
light.set_pull(Pull::Floating)?;
|
|
|
|
let mut charge_indicator = PinDriver::input_output(peripherals.gpio3.downgrade())?;
|
|
charge_indicator.set_pull(Pull::Floating)?;
|
|
charge_indicator.set_low()?;
|
|
|
|
let mut pump_expander = Pca9535Immediate::new(MutexDevice::new(&I2C_DRIVER), 32);
|
|
for pin in 0..8 {
|
|
let _ = pump_expander.pin_into_output(GPIOBank::Bank0, pin);
|
|
let _ = pump_expander.pin_into_output(GPIOBank::Bank1, pin);
|
|
let _ = pump_expander.pin_set_low(GPIOBank::Bank0, pin);
|
|
let _ = pump_expander.pin_set_low(GPIOBank::Bank1, pin);
|
|
}
|
|
|
|
|
|
|
|
let mppt_ina = SyncIna219::new(
|
|
MutexDevice::new(&I2C_DRIVER),
|
|
Address::from_pins(Pin::Vcc, Pin::Gnd),
|
|
);
|
|
|
|
let charger = match mppt_ina {
|
|
Ok(mut mppt_ina) => {
|
|
mppt_ina.set_configuration(Configuration {
|
|
reset: Default::default(),
|
|
bus_voltage_range: Default::default(),
|
|
shunt_voltage_range: Default::default(),
|
|
bus_resolution: Default::default(),
|
|
shunt_resolution: ina219::configuration::Resolution::Avg128,
|
|
operating_mode: Default::default(),
|
|
})?;
|
|
|
|
Charger::SolarMpptV1 {
|
|
mppt_ina,
|
|
solar_is_day,
|
|
charge_indicator,
|
|
}
|
|
}
|
|
Err(_) => Charger::ErrorInit {},
|
|
};
|
|
|
|
let pump_ina = match SyncIna219::new(
|
|
MutexDevice::new(&I2C_DRIVER),
|
|
Address::from_pins(Pin::Gnd, Pin::Sda),
|
|
) {
|
|
Ok(pump_ina) => Some(pump_ina),
|
|
Err(err) => {
|
|
log::info!("Error creating pump ina: {:?}", err);
|
|
None
|
|
}
|
|
};
|
|
|
|
let v = V4 {
|
|
rtc_module,
|
|
esp,
|
|
awake,
|
|
tank_sensor,
|
|
light,
|
|
general_fault,
|
|
pump_ina,
|
|
pump_expander,
|
|
config,
|
|
battery_monitor,
|
|
charger,
|
|
extra1,
|
|
extra2,
|
|
sensor,
|
|
};
|
|
Ok(Box::new(v))
|
|
}
|
|
|
|
impl<'a> BoardInteraction<'a> for V4<'a> {
|
|
fn get_tank_sensor(&mut self) -> Option<&mut TankSensor<'a>> {
|
|
Some(&mut self.tank_sensor)
|
|
}
|
|
|
|
fn get_esp(&mut self) -> &mut Esp<'a> {
|
|
&mut self.esp
|
|
}
|
|
|
|
fn get_config(&mut self) -> &PlantControllerConfig {
|
|
&self.config
|
|
}
|
|
|
|
fn get_battery_monitor(&mut self) -> &mut Box<dyn BatteryInteraction + Send> {
|
|
&mut self.battery_monitor
|
|
}
|
|
|
|
fn get_rtc_module(&mut self) -> &mut Box<dyn RTCModuleInteraction + Send> {
|
|
&mut self.rtc_module
|
|
}
|
|
|
|
fn set_charge_indicator(&mut self, charging: bool) -> anyhow::Result<()> {
|
|
self.charger.set_charge_indicator(charging)
|
|
}
|
|
|
|
fn deep_sleep(&mut self, duration_in_ms: u64) -> ! {
|
|
self.awake.set_low().unwrap();
|
|
self.charger.power_save();
|
|
deep_sleep(duration_in_ms);
|
|
}
|
|
|
|
fn is_day(&self) -> bool {
|
|
self.charger.is_day()
|
|
}
|
|
|
|
fn light(&mut self, enable: bool) -> anyhow::Result<()> {
|
|
unsafe { gpio_hold_dis(self.light.pin()) };
|
|
self.light.set_state(enable.into())?;
|
|
unsafe { gpio_hold_en(self.light.pin()) };
|
|
anyhow::Ok(())
|
|
}
|
|
|
|
fn pump(&mut self, plant: usize, enable: bool) -> anyhow::Result<()> {
|
|
if enable {
|
|
self.pump_expander
|
|
.pin_set_high(GPIOBank::Bank0, plant.try_into()?)?;
|
|
} else {
|
|
self.pump_expander
|
|
.pin_set_low(GPIOBank::Bank0, plant.try_into()?)?;
|
|
}
|
|
anyhow::Ok(())
|
|
}
|
|
|
|
fn pump_current(&mut self, _plant: usize) -> anyhow::Result<Current> {
|
|
//sensore is shared for all pumps, ignore plant id
|
|
match self.pump_ina.as_mut() {
|
|
None => {
|
|
bail!("pump current sensor not available");
|
|
}
|
|
Some(pump_ina) => {
|
|
let v = pump_ina.shunt_voltage().map(|v| {
|
|
let shunt_voltage = Voltage::from_microvolts(v.shunt_voltage_uv().abs() as f64);
|
|
let shut_value = Resistance::from_ohms(0.05_f64);
|
|
let current = shunt_voltage.as_volts() / shut_value.as_ohms();
|
|
Current::from_amperes(current)
|
|
})?;
|
|
Ok(v)
|
|
}
|
|
}
|
|
}
|
|
|
|
fn fault(&mut self, plant: usize, enable: bool) -> anyhow::Result<()> {
|
|
if enable {
|
|
self.pump_expander
|
|
.pin_set_high(GPIOBank::Bank1, plant.try_into()?)?
|
|
} else {
|
|
self.pump_expander
|
|
.pin_set_low(GPIOBank::Bank1, plant.try_into()?)?
|
|
}
|
|
anyhow::Ok(())
|
|
}
|
|
|
|
fn measure_moisture_hz(&mut self, plant: usize, sensor: Sensor) -> anyhow::Result<f32> {
|
|
self.sensor.measure_moisture_hz(plant, sensor)
|
|
}
|
|
|
|
fn general_fault(&mut self, enable: bool) {
|
|
unsafe { gpio_hold_dis(self.general_fault.pin()) };
|
|
self.general_fault.set_state(enable.into()).unwrap();
|
|
unsafe { gpio_hold_en(self.general_fault.pin()) };
|
|
}
|
|
|
|
fn test(&mut self) -> anyhow::Result<()> {
|
|
self.general_fault(true);
|
|
self.esp.delay.delay_ms(100);
|
|
self.general_fault(false);
|
|
self.esp.delay.delay_ms(500);
|
|
self.light(true)?;
|
|
self.esp.delay.delay_ms(500);
|
|
self.light(false)?;
|
|
self.esp.delay.delay_ms(500);
|
|
for i in 0..PLANT_COUNT {
|
|
self.fault(i, true)?;
|
|
self.esp.delay.delay_ms(500);
|
|
self.fault(i, false)?;
|
|
self.esp.delay.delay_ms(500);
|
|
}
|
|
for i in 0..PLANT_COUNT {
|
|
self.pump(i, true)?;
|
|
self.esp.delay.delay_ms(100);
|
|
self.pump(i, false)?;
|
|
self.esp.delay.delay_ms(100);
|
|
}
|
|
for plant in 0..PLANT_COUNT {
|
|
let a = self.measure_moisture_hz(plant, Sensor::A);
|
|
let b = self.measure_moisture_hz(plant, Sensor::B);
|
|
let aa = match a {
|
|
OkStd(a) => a as u32,
|
|
Err(_) => u32::MAX,
|
|
};
|
|
let bb = match b {
|
|
OkStd(b) => b as u32,
|
|
Err(_) => u32::MAX,
|
|
};
|
|
log(LogMessage::TestSensor, aa, bb, &plant.to_string(), "");
|
|
}
|
|
self.esp.delay.delay_ms(10);
|
|
anyhow::Ok(())
|
|
}
|
|
|
|
fn set_config(&mut self, config: PlantControllerConfig) -> anyhow::Result<()> {
|
|
self.config = config;
|
|
self.esp.save_config(&self.config)?;
|
|
anyhow::Ok(())
|
|
}
|
|
|
|
fn get_mptt_voltage(&mut self) -> anyhow::Result<Voltage> {
|
|
self.charger.get_mptt_voltage()
|
|
}
|
|
|
|
fn get_mptt_current(&mut self) -> anyhow::Result<Current> {
|
|
self.charger.get_mptt_current()
|
|
}
|
|
}
|