Merge branch 'can' into develop

board/PlantCtrlESP32.kicad_prl

@@ -1,6 +1,6 @@
 {
   "board": {
-    "active_layer": 4,
+    "active_layer": 0,
     "active_layer_preset": "All Layers",
     "auto_track_width": false,
     "hidden_netclasses": [],

board/PlantCtrlESP32.kicad_pro

@@ -472,6 +472,7 @@
       "single_global_label": "ignore",
       "unannotated": "error",
       "unconnected_wire_endpoint": "warning",
+      "undefined_netclass": "error",
       "unit_value_mismatch": "error",
       "unresolved_variable": "error",
       "wire_dangling": "error"

board/modules/MPPT/battery-charging.svg

@@ -0,0 +1,6 @@
+<svg xmlns="http://www.w3.org/2000/svg" width="16" height="16" fill="currentColor" class="bi bi-battery-charging" viewBox="0 0 16 16">
+  <path d="M9.585 2.568a.5.5 0 0 1 .226.58L8.677 6.832h1.99a.5.5 0 0 1 .364.843l-5.334 5.667a.5.5 0 0 1-.842-.49L5.99 9.167H4a.5.5 0 0 1-.364-.843l5.333-5.667a.5.5 0 0 1 .616-.09z"/>
+  <path d="M2 4h4.332l-.94 1H2a1 1 0 0 0-1 1v4a1 1 0 0 0 1 1h2.38l-.308 1H2a2 2 0 0 1-2-2V6a2 2 0 0 1 2-2"/>
+  <path d="M2 6h2.45L2.908 7.639A1.5 1.5 0 0 0 3.313 10H2zm8.595-2-.308 1H12a1 1 0 0 1 1 1v4a1 1 0 0 1-1 1H9.276l-.942 1H12a2 2 0 0 0 2-2V6a2 2 0 0 0-2-2z"/>
+  <path d="M12 10h-1.783l1.542-1.639q.146-.156.241-.34zm0-3.354V6h-.646a1.5 1.5 0 0 1 .646.646M16 8a1.5 1.5 0 0 1-1.5 1.5v-3A1.5 1.5 0 0 1 16 8"/>
+</svg>

board/modules/Sensors/Sensors/Sensor.pretty/Sensor.kicad_mod

@@ -182,40 +182,40 @@
 	)
 	(pad "9" thru_hole rect
 		(at 39.5 22.5)
-		(size 0.85 0.85)
+		(size 1.7 1.7)
-		(drill 0.5)
+		(drill 1)
 		(layers "*.Cu" "*.Mask")
 		(remove_unused_layers no)
 		(uuid "f01565c2-eadd-4451-9dea-2ebe28d872f0")
 	)
 	(pad "10" thru_hole rect
 		(at -0.5 15)
-		(size 0.85 0.85)
+		(size 1.7 1.7)
-		(drill 0.5)
+		(drill 1)
 		(layers "*.Cu" "*.Mask")
 		(remove_unused_layers no)
 		(uuid "56ec7c50-069f-4f46-9b83-ac18e4928930")
 	)
 	(pad "11" thru_hole rect
 		(at -43 22.5)
-		(size 0.85 0.85)
+		(size 1.7 1.7)
-		(drill 0.5)
+		(drill 1)
 		(layers "*.Cu" "*.Mask")
 		(remove_unused_layers no)
 		(uuid "f423be21-13b8-46de-8e19-e48325411a29")
 	)
 	(pad "12" thru_hole rect
 		(at -0.5 -12)
-		(size 0.85 0.85)
+		(size 1.7 1.7)
-		(drill 0.5)
+		(drill 1)
 		(layers "*.Cu" "*.Mask")
 		(remove_unused_layers no)
 		(uuid "536f0038-06c5-45e5-b1c8-898a364f6ec4")
 	)
 	(pad "13" thru_hole rect
 		(at 39.5 -16)
-		(size 0.85 0.85)
+		(size 1.7 1.7)
-		(drill 0.5)
+		(drill 1)
 		(layers "*.Cu" "*.Mask")
 		(remove_unused_layers no)
 		(uuid "3e0cdbaa-8219-48c4-bb0a-fd4f0e78a390")

board/modules/Sensors_can/Sensors/Sensor.pretty/Sensor.kicad_mod

@@ -0,0 +1,208 @@
+(footprint "Sensor"
+	(version 20241229)
+	(generator "pcbnew")
+	(generator_version "9.0")
+	(layer "F.Cu")
+	(property "Reference" "REF**"
+		(at 0 -0.5 0)
+		(unlocked yes)
+		(layer "F.SilkS")
+		(uuid "f71e9c26-7923-4e5c-828e-153927862740")
+		(effects
+			(font
+				(size 1 1)
+				(thickness 0.1)
+			)
+		)
+	)
+	(property "Value" "Sensor"
+		(at 0 1 0)
+		(unlocked yes)
+		(layer "F.Fab")
+		(uuid "d40c7203-0c06-49e1-8672-dbd216694fc8")
+		(effects
+			(font
+				(size 1 1)
+				(thickness 0.15)
+			)
+		)
+	)
+	(property "Datasheet" ""
+		(at 0 0 0)
+		(unlocked yes)
+		(layer "F.Fab")
+		(hide yes)
+		(uuid "6720cb18-0687-4d55-a6ad-3ccf0819eac2")
+		(effects
+			(font
+				(size 1 1)
+				(thickness 0.15)
+			)
+		)
+	)
+	(property "Description" ""
+		(at 0 0 0)
+		(unlocked yes)
+		(layer "F.Fab")
+		(hide yes)
+		(uuid "43905e6e-773d-4d5e-8d72-57c092c3495a")
+		(effects
+			(font
+				(size 1 1)
+				(thickness 0.15)
+			)
+		)
+	)
+	(attr smd)
+	(fp_line
+		(start -45 -18)
+		(end 41 -18)
+		(stroke
+			(width 0.1)
+			(type default)
+		)
+		(layer "F.SilkS")
+		(uuid "e63ec799-95c4-407e-acc9-9c7e6d3e330c")
+	)
+	(fp_line
+		(start -45 24)
+		(end -45 -18)
+		(stroke
+			(width 0.1)
+			(type default)
+		)
+		(layer "F.SilkS")
+		(uuid "a66c286b-432b-493d-9619-2dd4fbfdb21c")
+	)
+	(fp_line
+		(start -44 24)
+		(end -45 24)
+		(stroke
+			(width 0.1)
+			(type default)
+		)
+		(layer "F.SilkS")
+		(uuid "71526e68-71d4-4b13-ab74-482657a06849")
+	)
+	(fp_line
+		(start 41 -18)
+		(end 41 24)
+		(stroke
+			(width 0.1)
+			(type default)
+		)
+		(layer "F.SilkS")
+		(uuid "55554342-bbff-4d1b-b931-67fb7eaa5895")
+	)
+	(fp_line
+		(start 41 24)
+		(end -44 24)
+		(stroke
+			(width 0.1)
+			(type default)
+		)
+		(layer "F.SilkS")
+		(uuid "2dc0ee59-36f6-407e-821a-c6acfe3ea887")
+	)
+	(fp_text user "${REFERENCE}"
+		(at 0 2.5 0)
+		(unlocked yes)
+		(layer "F.Fab")
+		(uuid "befc0725-b201-4f81-b0dc-b327becad9ba")
+		(effects
+			(font
+				(size 1 1)
+				(thickness 0.15)
+			)
+		)
+	)
+	(pad "1" thru_hole rect
+		(at -42.4 -15.3)
+		(size 1.7 1.7)
+		(drill 1)
+		(layers "*.Cu" "*.Mask")
+		(remove_unused_layers no)
+		(uuid "5538ac99-6e48-4111-a3df-8ff33be72ff3")
+	)
+	(pad "2" thru_hole circle
+		(at -42.4 -12.76)
+		(size 1.7 1.7)
+		(drill 1)
+		(layers "*.Cu" "*.Mask")
+		(remove_unused_layers no)
+		(uuid "0c1d4a6c-7871-46ae-a262-a8223571975e")
+	)
+	(pad "3" thru_hole circle
+		(at -42.4 -10.22)
+		(size 1.7 1.7)
+		(drill 1)
+		(layers "*.Cu" "*.Mask")
+		(remove_unused_layers no)
+		(uuid "70df4148-0415-45a2-8365-0977fcda45a1")
+	)
+	(pad "4" thru_hole circle
+		(at -42.4 -7.68)
+		(size 1.7 1.7)
+		(drill 1)
+		(layers "*.Cu" "*.Mask")
+		(remove_unused_layers no)
+		(uuid "179dd332-2ab2-4917-91ec-35f232b45ce3")
+	)
+	(pad "5" thru_hole circle
+		(at -42.4 -5.14)
+		(size 1.7 1.7)
+		(drill 1)
+		(layers "*.Cu" "*.Mask")
+		(remove_unused_layers no)
+		(uuid "17bc8f3a-4727-4e31-90f4-8252dff5ad1c")
+	)
+	(pad "6" thru_hole circle
+		(at -42.4 -2.6)
+		(size 1.7 1.7)
+		(drill 1)
+		(layers "*.Cu" "*.Mask")
+		(remove_unused_layers no)
+		(uuid "eee06414-e977-45a8-a5e0-618644284d45")
+	)
+	(pad "7" thru_hole rect
+		(at -0.5 -12)
+		(size 1.7 1.7)
+		(drill 1)
+		(layers "*.Cu" "*.Mask")
+		(remove_unused_layers no)
+		(uuid "536f0038-06c5-45e5-b1c8-898a364f6ec4")
+	)
+	(pad "8" thru_hole rect
+		(at 39.5 -16)
+		(size 1.7 1.7)
+		(drill 1)
+		(layers "*.Cu" "*.Mask")
+		(remove_unused_layers no)
+		(uuid "3e0cdbaa-8219-48c4-bb0a-fd4f0e78a390")
+	)
+	(pad "9" thru_hole rect
+		(at 39.5 22.5)
+		(size 1.7 1.7)
+		(drill 1)
+		(layers "*.Cu" "*.Mask")
+		(remove_unused_layers no)
+		(uuid "f01565c2-eadd-4451-9dea-2ebe28d872f0")
+	)
+	(pad "10" thru_hole rect
+		(at -0.5 15)
+		(size 1.7 1.7)
+		(drill 1)
+		(layers "*.Cu" "*.Mask")
+		(remove_unused_layers no)
+		(uuid "56ec7c50-069f-4f46-9b83-ac18e4928930")
+	)
+	(pad "11" thru_hole rect
+		(at -43 22.5)
+		(size 1.7 1.7)
+		(drill 1)
+		(layers "*.Cu" "*.Mask")
+		(remove_unused_layers no)
+		(uuid "f423be21-13b8-46de-8e19-e48325411a29")
+	)
+	(embedded_fonts no)
+)

board/modules/Sensors_can/Sensors/Sensors.kicad_prl

@@ -0,0 +1,136 @@
+{
+  "board": {
+    "active_layer": 6,
+    "active_layer_preset": "All Layers",
+    "auto_track_width": false,
+    "hidden_netclasses": [],
+    "hidden_nets": [],
+    "high_contrast_mode": 0,
+    "net_color_mode": 1,
+    "opacity": {
+      "images": 0.6,
+      "pads": 1.0,
+      "shapes": 1.0,
+      "tracks": 1.0,
+      "vias": 1.0,
+      "zones": 0.6
+    },
+    "selection_filter": {
+      "dimensions": true,
+      "footprints": true,
+      "graphics": true,
+      "keepouts": true,
+      "lockedItems": false,
+      "otherItems": true,
+      "pads": true,
+      "text": true,
+      "tracks": true,
+      "vias": true,
+      "zones": true
+    },
+    "visible_items": [
+      "vias",
+      "footprint_text",
+      "footprint_anchors",
+      "ratsnest",
+      "grid",
+      "footprints_front",
+      "footprints_back",
+      "footprint_values",
+      "footprint_references",
+      "tracks",
+      "drc_errors",
+      "drawing_sheet",
+      "bitmaps",
+      "pads",
+      "zones",
+      "drc_warnings",
+      "locked_item_shadows",
+      "conflict_shadows",
+      "shapes"
+    ],
+    "visible_layers": "ffffffff_ffffffff_ffffffff_ffffffff",
+    "zone_display_mode": 1
+  },
+  "git": {
+    "repo_type": "",
+    "repo_username": "",
+    "ssh_key": ""
+  },
+  "meta": {
+    "filename": "Sensors.kicad_prl",
+    "version": 5
+  },
+  "net_inspector_panel": {
+    "col_hidden": [
+      false,
+      false,
+      false,
+      false,
+      false,
+      false,
+      false,
+      false,
+      false,
+      false,
+      false,
+      false
+    ],
+    "col_order": [
+      0,
+      1,
+      2,
+      3,
+      4,
+      5,
+      6,
+      7,
+      8,
+      9,
+      10,
+      11
+    ],
+    "col_widths": [
+      0,
+      0,
+      0,
+      0,
+      0,
+      0,
+      0,
+      0,
+      0,
+      0,
+      0,
+      0
+    ],
+    "custom_group_rules": [],
+    "expanded_rows": [],
+    "filter_by_net_name": true,
+    "filter_by_netclass": true,
+    "filter_text": "",
+    "group_by_constraint": false,
+    "group_by_netclass": false,
+    "show_unconnected_nets": false,
+    "show_zero_pad_nets": false,
+    "sort_ascending": true,
+    "sorting_column": 0
+  },
+  "open_jobsets": [],
+  "project": {
+    "files": []
+  },
+  "schematic": {
+    "selection_filter": {
+      "graphics": true,
+      "images": true,
+      "labels": true,
+      "lockedItems": false,
+      "otherItems": true,
+      "pins": true,
+      "symbols": true,
+      "text": true,
+      "wires": true
+    }
+  }
+}

board/modules/Sensors_can/Sensors/Sensors.kicad_pro

@@ -0,0 +1,674 @@
+{
+  "board": {
+    "3dviewports": [],
+    "design_settings": {
+      "defaults": {
+        "apply_defaults_to_fp_fields": false,
+        "apply_defaults_to_fp_shapes": false,
+        "apply_defaults_to_fp_text": false,
+        "board_outline_line_width": 0.05,
+        "copper_line_width": 0.2,
+        "copper_text_italic": false,
+        "copper_text_size_h": 1.5,
+        "copper_text_size_v": 1.5,
+        "copper_text_thickness": 0.3,
+        "copper_text_upright": false,
+        "courtyard_line_width": 0.05,
+        "dimension_precision": 4,
+        "dimension_units": 3,
+        "dimensions": {
+          "arrow_length": 1270000,
+          "extension_offset": 500000,
+          "keep_text_aligned": true,
+          "suppress_zeroes": true,
+          "text_position": 0,
+          "units_format": 0
+        },
+        "fab_line_width": 0.1,
+        "fab_text_italic": false,
+        "fab_text_size_h": 1.0,
+        "fab_text_size_v": 1.0,
+        "fab_text_thickness": 0.15,
+        "fab_text_upright": false,
+        "other_line_width": 0.1,
+        "other_text_italic": false,
+        "other_text_size_h": 1.0,
+        "other_text_size_v": 1.0,
+        "other_text_thickness": 0.15,
+        "other_text_upright": false,
+        "pads": {
+          "drill": 0.8,
+          "height": 1.27,
+          "width": 2.54
+        },
+        "silk_line_width": 0.1,
+        "silk_text_italic": false,
+        "silk_text_size_h": 1.0,
+        "silk_text_size_v": 1.0,
+        "silk_text_thickness": 0.1,
+        "silk_text_upright": false,
+        "zones": {
+          "min_clearance": 0.5
+        }
+      },
+      "diff_pair_dimensions": [
+        {
+          "gap": 0.0,
+          "via_gap": 0.0,
+          "width": 0.0
+        }
+      ],
+      "drc_exclusions": [],
+      "meta": {
+        "version": 2
+      },
+      "rule_severities": {
+        "annular_width": "error",
+        "clearance": "error",
+        "connection_width": "warning",
+        "copper_edge_clearance": "error",
+        "copper_sliver": "warning",
+        "courtyards_overlap": "error",
+        "creepage": "error",
+        "diff_pair_gap_out_of_range": "error",
+        "diff_pair_uncoupled_length_too_long": "error",
+        "drill_out_of_range": "error",
+        "duplicate_footprints": "warning",
+        "extra_footprint": "warning",
+        "footprint": "error",
+        "footprint_filters_mismatch": "ignore",
+        "footprint_symbol_mismatch": "warning",
+        "footprint_type_mismatch": "ignore",
+        "hole_clearance": "error",
+        "hole_to_hole": "warning",
+        "holes_co_located": "warning",
+        "invalid_outline": "error",
+        "isolated_copper": "warning",
+        "item_on_disabled_layer": "error",
+        "items_not_allowed": "error",
+        "length_out_of_range": "error",
+        "lib_footprint_issues": "warning",
+        "lib_footprint_mismatch": "warning",
+        "malformed_courtyard": "ignore",
+        "microvia_drill_out_of_range": "error",
+        "mirrored_text_on_front_layer": "warning",
+        "missing_courtyard": "ignore",
+        "missing_footprint": "warning",
+        "net_conflict": "warning",
+        "nonmirrored_text_on_back_layer": "warning",
+        "npth_inside_courtyard": "ignore",
+        "padstack": "warning",
+        "pth_inside_courtyard": "ignore",
+        "shorting_items": "error",
+        "silk_edge_clearance": "ignore",
+        "silk_over_copper": "warning",
+        "silk_overlap": "warning",
+        "skew_out_of_range": "error",
+        "solder_mask_bridge": "error",
+        "starved_thermal": "warning",
+        "text_height": "warning",
+        "text_on_edge_cuts": "error",
+        "text_thickness": "warning",
+        "through_hole_pad_without_hole": "error",
+        "too_many_vias": "error",
+        "track_angle": "error",
+        "track_dangling": "warning",
+        "track_segment_length": "error",
+        "track_width": "error",
+        "tracks_crossing": "error",
+        "unconnected_items": "error",
+        "unresolved_variable": "error",
+        "via_dangling": "warning",
+        "zones_intersect": "error"
+      },
+      "rules": {
+        "max_error": 0.005,
+        "min_clearance": 0.0,
+        "min_connection": 0.0,
+        "min_copper_edge_clearance": 0.5,
+        "min_groove_width": 0.0,
+        "min_hole_clearance": 0.15,
+        "min_hole_to_hole": 0.25,
+        "min_microvia_diameter": 0.2,
+        "min_microvia_drill": 0.1,
+        "min_resolved_spokes": 2,
+        "min_silk_clearance": 0.0,
+        "min_text_height": 0.8,
+        "min_text_thickness": 0.08,
+        "min_through_hole_diameter": 0.25,
+        "min_track_width": 0.0,
+        "min_via_annular_width": 0.05,
+        "min_via_diameter": 0.25,
+        "solder_mask_to_copper_clearance": 0.005,
+        "use_height_for_length_calcs": true
+      },
+      "teardrop_options": [
+        {
+          "td_onpthpad": true,
+          "td_onroundshapesonly": false,
+          "td_onsmdpad": true,
+          "td_ontrackend": false,
+          "td_onvia": true
+        }
+      ],
+      "teardrop_parameters": [
+        {
+          "td_allow_use_two_tracks": true,
+          "td_curve_segcount": 0,
+          "td_height_ratio": 1.0,
+          "td_length_ratio": 0.5,
+          "td_maxheight": 2.0,
+          "td_maxlen": 1.0,
+          "td_on_pad_in_zone": false,
+          "td_target_name": "td_round_shape",
+          "td_width_to_size_filter_ratio": 0.9
+        },
+        {
+          "td_allow_use_two_tracks": true,
+          "td_curve_segcount": 0,
+          "td_height_ratio": 1.0,
+          "td_length_ratio": 0.5,
+          "td_maxheight": 2.0,
+          "td_maxlen": 1.0,
+          "td_on_pad_in_zone": false,
+          "td_target_name": "td_rect_shape",
+          "td_width_to_size_filter_ratio": 0.9
+        },
+        {
+          "td_allow_use_two_tracks": true,
+          "td_curve_segcount": 0,
+          "td_height_ratio": 1.0,
+          "td_length_ratio": 0.5,
+          "td_maxheight": 2.0,
+          "td_maxlen": 1.0,
+          "td_on_pad_in_zone": false,
+          "td_target_name": "td_track_end",
+          "td_width_to_size_filter_ratio": 0.9
+        }
+      ],
+      "track_widths": [
+        0.0,
+        0.1,
+        0.2,
+        0.5
+      ],
+      "tuning_pattern_settings": {
+        "diff_pair_defaults": {
+          "corner_radius_percentage": 80,
+          "corner_style": 1,
+          "max_amplitude": 1.0,
+          "min_amplitude": 0.2,
+          "single_sided": false,
+          "spacing": 1.0
+        },
+        "diff_pair_skew_defaults": {
+          "corner_radius_percentage": 80,
+          "corner_style": 1,
+          "max_amplitude": 1.0,
+          "min_amplitude": 0.2,
+          "single_sided": false,
+          "spacing": 0.6
+        },
+        "single_track_defaults": {
+          "corner_radius_percentage": 80,
+          "corner_style": 1,
+          "max_amplitude": 1.0,
+          "min_amplitude": 0.2,
+          "single_sided": false,
+          "spacing": 0.6
+        }
+      },
+      "via_dimensions": [
+        {
+          "diameter": 0.0,
+          "drill": 0.0
+        },
+        {
+          "diameter": 0.3,
+          "drill": 0.25
+        }
+      ],
+      "zones_allow_external_fillets": false
+    },
+    "ipc2581": {
+      "dist": "",
+      "distpn": "",
+      "internal_id": "",
+      "mfg": "",
+      "mpn": ""
+    },
+    "layer_pairs": [],
+    "layer_presets": [],
+    "viewports": []
+  },
+  "boards": [],
+  "cvpcb": {
+    "equivalence_files": []
+  },
+  "erc": {
+    "erc_exclusions": [],
+    "meta": {
+      "version": 0
+    },
+    "pin_map": [
+      [
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        1,
+        0,
+        0,
+        0,
+        0,
+        2
+      ],
+      [
+        0,
+        2,
+        0,
+        1,
+        0,
+        0,
+        1,
+        0,
+        2,
+        2,
+        2,
+        2
+      ],
+      [
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        1,
+        0,
+        1,
+        0,
+        1,
+        2
+      ],
+      [
+        0,
+        1,
+        0,
+        0,
+        0,
+        0,
+        1,
+        1,
+        2,
+        1,
+        1,
+        2
+      ],
+      [
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        1,
+        0,
+        0,
+        0,
+        0,
+        2
+      ],
+      [
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        2
+      ],
+      [
+        1,
+        1,
+        1,
+        1,
+        1,
+        0,
+        1,
+        1,
+        1,
+        1,
+        1,
+        2
+      ],
+      [
+        0,
+        0,
+        0,
+        1,
+        0,
+        0,
+        1,
+        0,
+        0,
+        0,
+        0,
+        2
+      ],
+      [
+        0,
+        2,
+        1,
+        2,
+        0,
+        0,
+        1,
+        0,
+        2,
+        2,
+        2,
+        2
+      ],
+      [
+        0,
+        2,
+        0,
+        1,
+        0,
+        0,
+        1,
+        0,
+        2,
+        0,
+        0,
+        2
+      ],
+      [
+        0,
+        2,
+        1,
+        1,
+        0,
+        0,
+        1,
+        0,
+        2,
+        0,
+        0,
+        2
+      ],
+      [
+        2,
+        2,
+        2,
+        2,
+        2,
+        2,
+        2,
+        2,
+        2,
+        2,
+        2,
+        2
+      ]
+    ],
+    "rule_severities": {
+      "bus_definition_conflict": "error",
+      "bus_entry_needed": "error",
+      "bus_to_bus_conflict": "error",
+      "bus_to_net_conflict": "error",
+      "different_unit_footprint": "error",
+      "different_unit_net": "error",
+      "duplicate_reference": "error",
+      "duplicate_sheet_names": "error",
+      "endpoint_off_grid": "warning",
+      "extra_units": "error",
+      "footprint_filter": "ignore",
+      "footprint_link_issues": "warning",
+      "four_way_junction": "ignore",
+      "global_label_dangling": "warning",
+      "hier_label_mismatch": "error",
+      "label_dangling": "error",
+      "label_multiple_wires": "warning",
+      "lib_symbol_issues": "warning",
+      "lib_symbol_mismatch": "warning",
+      "missing_bidi_pin": "warning",
+      "missing_input_pin": "warning",
+      "missing_power_pin": "error",
+      "missing_unit": "warning",
+      "multiple_net_names": "warning",
+      "net_not_bus_member": "warning",
+      "no_connect_connected": "warning",
+      "no_connect_dangling": "warning",
+      "pin_not_connected": "error",
+      "pin_not_driven": "error",
+      "pin_to_pin": "ignore",
+      "power_pin_not_driven": "ignore",
+      "same_local_global_label": "warning",
+      "similar_label_and_power": "warning",
+      "similar_labels": "warning",
+      "similar_power": "warning",
+      "simulation_model_issue": "ignore",
+      "single_global_label": "ignore",
+      "unannotated": "error",
+      "unconnected_wire_endpoint": "warning",
+      "unit_value_mismatch": "error",
+      "unresolved_variable": "error",
+      "wire_dangling": "error"
+    }
+  },
+  "libraries": {
+    "pinned_footprint_libs": [],
+    "pinned_symbol_libs": []
+  },
+  "meta": {
+    "filename": "Sensors.kicad_pro",
+    "version": 3
+  },
+  "net_settings": {
+    "classes": [
+      {
+        "bus_width": 12,
+        "clearance": 0.15,
+        "diff_pair_gap": 0.25,
+        "diff_pair_via_gap": 0.25,
+        "diff_pair_width": 0.2,
+        "line_style": 0,
+        "microvia_diameter": 0.3,
+        "microvia_drill": 0.1,
+        "name": "Default",
+        "pcb_color": "rgba(0, 0, 0, 0.000)",
+        "priority": 2147483647,
+        "schematic_color": "rgba(0, 0, 0, 0.000)",
+        "track_width": 0.2,
+        "via_diameter": 0.6,
+        "via_drill": 0.3,
+        "wire_width": 6
+      }
+    ],
+    "meta": {
+      "version": 4
+    },
+    "net_colors": null,
+    "netclass_assignments": null,
+    "netclass_patterns": []
+  },
+  "pcbnew": {
+    "last_paths": {
+      "gencad": "",
+      "idf": "",
+      "netlist": "",
+      "plot": "",
+      "pos_files": "",
+      "specctra_dsn": "",
+      "step": "Sensors.step",
+      "svg": "",
+      "vrml": ""
+    },
+    "page_layout_descr_file": ""
+  },
+  "schematic": {
+    "annotate_start_num": 0,
+    "bom_export_filename": "${PROJECTNAME}.csv",
+    "bom_fmt_presets": [],
+    "bom_fmt_settings": {
+      "field_delimiter": ",",
+      "keep_line_breaks": false,
+      "keep_tabs": false,
+      "name": "CSV",
+      "ref_delimiter": ",",
+      "ref_range_delimiter": "",
+      "string_delimiter": "\""
+    },
+    "bom_presets": [],
+    "bom_settings": {
+      "exclude_dnp": false,
+      "fields_ordered": [
+        {
+          "group_by": false,
+          "label": "Reference",
+          "name": "Reference",
+          "show": true
+        },
+        {
+          "group_by": true,
+          "label": "Value",
+          "name": "Value",
+          "show": true
+        },
+        {
+          "group_by": true,
+          "label": "Footprint",
+          "name": "Footprint",
+          "show": true
+        },
+        {
+          "group_by": false,
+          "label": "Datasheet",
+          "name": "Datasheet",
+          "show": true
+        },
+        {
+          "group_by": false,
+          "label": "Description",
+          "name": "Description",
+          "show": false
+        },
+        {
+          "group_by": false,
+          "label": "Qty",
+          "name": "${QUANTITY}",
+          "show": true
+        },
+        {
+          "group_by": false,
+          "label": "#",
+          "name": "${ITEM_NUMBER}",
+          "show": false
+        },
+        {
+          "group_by": false,
+          "label": "LCSC_PART_NUMBER",
+          "name": "LCSC_PART_NUMBER",
+          "show": true
+        },
+        {
+          "group_by": false,
+          "label": "Sim.Device",
+          "name": "Sim.Device",
+          "show": false
+        },
+        {
+          "group_by": false,
+          "label": "Sim.Pins",
+          "name": "Sim.Pins",
+          "show": false
+        },
+        {
+          "group_by": false,
+          "label": "Sim.Type",
+          "name": "Sim.Type",
+          "show": false
+        },
+        {
+          "group_by": true,
+          "label": "DNP",
+          "name": "${DNP}",
+          "show": true
+        },
+        {
+          "group_by": true,
+          "label": "Exclude from BOM",
+          "name": "${EXCLUDE_FROM_BOM}",
+          "show": true
+        },
+        {
+          "group_by": true,
+          "label": "Exclude from Board",
+          "name": "${EXCLUDE_FROM_BOARD}",
+          "show": true
+        }
+      ],
+      "filter_string": "",
+      "group_symbols": true,
+      "include_excluded_from_bom": true,
+      "name": "",
+      "sort_asc": true,
+      "sort_field": "Reference"
+    },
+    "connection_grid_size": 50.0,
+    "drawing": {
+      "dashed_lines_dash_length_ratio": 12.0,
+      "dashed_lines_gap_length_ratio": 3.0,
+      "default_line_thickness": 6.0,
+      "default_text_size": 50.0,
+      "field_names": [],
+      "intersheets_ref_own_page": false,
+      "intersheets_ref_prefix": "",
+      "intersheets_ref_short": false,
+      "intersheets_ref_show": false,
+      "intersheets_ref_suffix": "",
+      "junction_size_choice": 3,
+      "label_size_ratio": 0.375,
+      "operating_point_overlay_i_precision": 3,
+      "operating_point_overlay_i_range": "~A",
+      "operating_point_overlay_v_precision": 3,
+      "operating_point_overlay_v_range": "~V",
+      "overbar_offset_ratio": 1.23,
+      "pin_symbol_size": 25.0,
+      "text_offset_ratio": 0.15
+    },
+    "legacy_lib_dir": "",
+    "legacy_lib_list": [],
+    "meta": {
+      "version": 1
+    },
+    "net_format_name": "",
+    "page_layout_descr_file": "",
+    "plot_directory": "",
+    "space_save_all_events": true,
+    "spice_current_sheet_as_root": false,
+    "spice_external_command": "spice \"%I\"",
+    "spice_model_current_sheet_as_root": true,
+    "spice_save_all_currents": false,
+    "spice_save_all_dissipations": false,
+    "spice_save_all_voltages": false,
+    "subpart_first_id": 65,
+    "subpart_id_separator": 0
+  },
+  "sheets": [
+    [
+      "46346c04-8bed-48b4-837b-9342dd403232",
+      "Root"
+    ]
+  ],
+  "text_variables": {}
+}

board/modules/Sensors_can/Sensors/sym-lib-table

@@ -0,0 +1,4 @@
+(sym_lib_table
+  (version 7)
+  (lib (name "Modules")(type "KiCad")(uri "/home/empire/workspace/PlantCtrl/board/modules/Modules.kicad_sym")(options "")(descr ""))
+)

board/modules/Sensors_can/ch32-sensor/.cargo/config.toml

@@ -0,0 +1,14 @@
+[build]
+target = "riscv32imc-unknown-none-elf"
+
+[target."riscv32imc-unknown-none-elf"]
+rustflags = [
+#  "-C", "link-arg=-Tlink.x",
+]
+# runner = "riscv64-unknown-elf-gdb -q -x openocd.gdb"
+# runner = "riscv-none-embed-gdb -q -x openocd.gdb"
+# runner = "gdb -q -x openocd.gdb"
+# runner = "wlink -v flash"
+
+runner = "wlink -v flash --enable-sdi-print --watch-serial --erase"
+# runner = "wlink -v flash"

board/modules/Sensors_can/ch32-sensor/.gdbinit

@@ -0,0 +1,7 @@
+target extended-remote :3333
+set remotetimeout 2000
+
+#symbol-file target/riscv32imc-unknown-none-elf/release/ch32v203-examples
+file target/riscv32imc-unknown-none-elf/release/bms
+
+monitor reset halt

board/modules/Sensors_can/ch32-sensor/.gitignore

@@ -0,0 +1 @@
+target

board/modules/Sensors_can/ch32-sensor/Cargo.toml

@@ -0,0 +1,43 @@
+[package]
+name = "bms"
+version = "0.1.0"
+edition = "2021"
+
+[dependencies]
+ch32-hal = { git = "https://github.com/ch32-rs/ch32-hal", features = [
+    "ch32v203c8t6",
+    "memory-x",
+    "embassy",
+    "rt",
+    "time-driver-tim2",
+], default-features = false }
+
+embassy-executor = { version = "0.7.0", features = [
+    "arch-riscv32",
+    "executor-thread",
+] }
+
+embassy-time = { version = "0.4.0" }
+embassy-usb = { version = "0.3.0" }
+embassy-futures = { version = "0.1.0" }
+
+# This is okay because we should automatically use whatever ch32-hal uses
+qingke-rt = "*"
+qingke = "*"
+
+panic-halt = "1.0"
+
+embedded-hal = "1.0.0"
+heapless = "0.8.0"
+micromath = { version = "2.1.0", features = ["num-traits"] }
+embedded-can = "0.4.1"
+
+[profile.dev]
+#lto = true
+opt-level = 1
+
+[profile.release]
+strip = false   # symbols are not flashed to the microcontroller, so don't strip them.
+#lto = true
+debug = true
+opt-level = "z" # Optimize for size.

board/modules/Sensors_can/ch32-sensor/README.md

@@ -0,0 +1,72 @@
+
+# ch32v203-bms
+
+A simple battery management controller software.
+
+## CAN bus and hardware address
+
+This firmware exposes a CAN interface on the CH32V203 and uses 4 hardware address pins to allow up to 16 sensors on the same bus.
+
+- CAN pins (default mapping):
+  - CAN RX: PA11
+  - CAN TX: PA12
+- Address select pins (with internal pull-ups):
+  - A0: PA0
+  - A1: PA1
+  - A2: PA2
+  - A3: PA3
+
+Wire each address pin to GND to set its corresponding bit to 1. The 4-bit address range is 0..15. The node’s CAN Standard ID is `0x100 | addr`, i.e. 0x100..0x10F. The CAN acceptance filter is configured to only accept frames with the node’s own ID.
+
+Adjust the pins above if your PCB routes CAN or address lines to different pads.
+
+## 555 timer (software) emulation mode
+
+To save the BOM cost of a classic NE555 in simple oscillator applications, this firmware implements a minimal 555-like Schmitt trigger using the MCU’s ADC and a GPIO, approximating the behavior when the capacitor is charged/discharged via Q through a resistor, and the combined Trigger/Threshold senses the capacitor node.
+
+- Pins used:
+  - Q output: PB2
+  - Combined Trigger/Threshold (ADC input): PA0
+- Wiring:
+  - PB2 (Q) -> series resistor R -> capacitor node
+  - Capacitor node -> capacitor to GND
+  - Capacitor node -> PA0 (ADC input)
+- Behavior:
+  - When ADC(PA0) <= ~1/3 Vref, PB2 is driven High.
+  - When ADC(PA0) >= ~2/3 Vref, PB2 is driven Low.
+  - Hysteresis avoids chatter; the actual charge/discharge dynamics follow your chosen R and C.
+- Notes:
+  - Use an appropriate resistor from PB2 to the capacitor to set oscillation frequency. Start with 10k..100k and adjust with C.
+  - Ensure PA0 is routed to the capacitor node and left high impedance (no strong pull-ups/downs) so the ADC can sense the analog voltage.
+  - PB2 drives the on-board LED (if present), so the LED might blink at the oscillation frequency.
+
+This mode is implemented in `src/main.rs` using `hal::adc::Adc::convert(&mut pin, SampleTime::...)` to take periodic samples and a simple state machine to toggle the Q output based on ~1/3 and ~2/3 Vref thresholds.
+
+## Building
+
+``` sh
+cargo build --release
+```
+
+## Flash
+
+``` sh
+wchisp config reset
+wchip wchisp flash target/riscv32imc-unknown-none-elf/release/bms
+```
+
+## Debugging
+
+For debugging purposes a container file is provided together with wrapper scripts to start the containerized `openocd` and `riscv-gdb` transparently. The wrapper scripts assume that `podman` is setup.
+
+Starting Debug server 
+
+```
+./bin/openocd
+```
+
+Connecting with gdb for interactive debugging
+
+```
+./bin/gdb -f target/riscv32imc-unknown-none-elf/release/bms
+```

board/modules/Sensors_can/ch32-sensor/bin/build-wch-tools-container.sh

@@ -0,0 +1,10 @@
+#!/usr/bin/env bash
+
+set -euo pipefail
+
+CONTAINER_NAME="localhost/wch-dev-tools:latest"
+CONTAINER_TOOLS_BASEDIR="$(dirname "$(readlink -f "$0")")"
+
+pushd "$CONTAINER_TOOLS_BASEDIR"
+podman build -t "$CONTAINER_NAME" -f "../wch-tools.Containerfile" .
+popd

board/modules/Sensors_can/ch32-sensor/bin/gdb

@@ -0,0 +1,29 @@
+#!/usr/bin/env bash
+
+set -euo pipefail
+
+CONTAINER_IMAGE="localhost/wch-dev-tools:latest"
+CONTAINER_TOOLS_BASEDIR="$(dirname "$(readlink -f "$0")")"
+
+function _fatal {
+	echo -e "\e[31mERROR\e[0m   $(</dev/stdin)$*" 1>&2
+	exit 1
+}
+
+declare -a PODMAN_ARGS=(
+	"--rm" "-i" "--log-driver=none"
+    "--network=host"
+    "--pid=host"
+	"-v" "$PWD:$PWD:rw"
+	"-w" "$PWD"
+)
+
+[[ -t 1 ]] && PODMAN_ARGS+=("-t")
+
+if ! podman image exists "$CONTAINER_IMAGE"; then
+    #attempt to build container
+    "$CONTAINER_TOOLS_BASEDIR/build-wch-tools-container.sh" 1>&2 ||
+        _fatal "faild to build local image, cannot continue! … please ensure you have an internet connection"
+fi
+
+podman run "${PODMAN_ARGS[@]}" --entrypoint riscv-none-elf-gdb-py3 "$CONTAINER_IMAGE" "$@"

board/modules/Sensors_can/ch32-sensor/bin/openocd

@@ -0,0 +1,44 @@
+#!/usr/bin/env bash
+
+set -euo pipefail
+
+CONTAINER_IMAGE="localhost/wch-dev-tools:latest"
+CONTAINER_TOOLS_BASEDIR="$(dirname "$(readlink -f "$0")")"
+
+function _fatal {
+	echo -e "\e[31mERROR\e[0m   $(</dev/stdin)$*" 1>&2
+	exit 1
+}
+
+declare -a PODMAN_ARGS=(
+	"--rm" "-i" "--log-driver=none"
+    "--network=host"
+	"-v" "$PWD:$PWD:rw"
+	"-w" "$PWD"
+)
+
+for device in /dev/bus/usb/*/*; do
+    if udevadm info "$device" | grep -q "ID_VENDOR=wch.cn" && \
+       udevadm info "$device" | grep -q "ID_MODEL=WCH-Link"; then
+        DEBUGGER_DEV_PATH="$device"
+        break
+    fi
+done
+
+if [[ -z "${DEBUGGER_DEV_PATH:-}" ]]; then
+    echo "Could not find hardware debugger … Exiting!" 1>&2
+    exit 1
+else
+    # add jlink to podman device
+    PODMAN_ARGS+=("--device=$DEBUGGER_DEV_PATH")
+fi
+
+[[ -t 1 ]] && PODMAN_ARGS+=("-t")
+
+if ! podman image exists "$CONTAINER_IMAGE"; then
+    #attempt to build container
+    "$CONTAINER_TOOLS_BASEDIR/build-wch-tools-container.sh" 1>&2 ||
+        _fatal "faild to build local image, cannot continue! … please ensure you have an internet connection"
+fi
+
+podman run "${PODMAN_ARGS[@]}" --entrypoint openocd "$CONTAINER_IMAGE" "$@"

board/modules/Sensors_can/ch32-sensor/build.rs

@@ -0,0 +1,11 @@
+fn main() {
+    // println!("cargo:rustc-link-arg-bins=--nmagic");
+    println!("cargo:rustc-link-arg-bins=-Tlink.x");
+    // println!("cargo:rustc-link-arg-bins=-Tdefmt.x");
+
+    let out_dir = std::env::var("OUT_DIR").unwrap();
+    let out_dir = std::path::PathBuf::from(out_dir);
+    std::fs::write(out_dir.join("memory.x"), include_bytes!("memory.x")).unwrap();
+    println!("cargo:rustc-link-search={}", out_dir.display());
+    println!("cargo:rerun-if-changed=memory.x");
+}

board/modules/Sensors_can/ch32-sensor/memory.x

@@ -0,0 +1,125 @@
+/* CH32V203c8t6 */
+MEMORY
+{
+    FLASH : ORIGIN = 0x00000000, LENGTH =   64K /* BANK_1 */
+    RAM   : ORIGIN = 0x20000000, LENGTH =   20K
+}
+REGION_ALIAS("REGION_TEXT", FLASH);
+REGION_ALIAS("REGION_RODATA", FLASH);
+REGION_ALIAS("REGION_DATA", RAM);
+REGION_ALIAS("REGION_BSS", RAM);
+REGION_ALIAS("REGION_HEAP", RAM);
+REGION_ALIAS("REGION_STACK", RAM);
+
+/* fault handlers */
+
+PROVIDE(InstructionMisaligned = ExceptionHandler);
+PROVIDE(InstructionFault = ExceptionHandler);
+PROVIDE(IllegalInstruction = ExceptionHandler);
+PROVIDE(Breakpoint = ExceptionHandler);
+PROVIDE(LoadMisaligned = ExceptionHandler);
+PROVIDE(LoadFault = ExceptionHandler);
+PROVIDE(StoreMisaligned = ExceptionHandler);
+PROVIDE(StoreFault = ExceptionHandler);;
+PROVIDE(UserEnvCall = ExceptionHandler);
+PROVIDE(SupervisorEnvCall = ExceptionHandler);
+PROVIDE(MachineEnvCall = ExceptionHandler);
+PROVIDE(InstructionPageFault = ExceptionHandler);
+PROVIDE(LoadPageFault = ExceptionHandler);
+PROVIDE(StorePageFault = ExceptionHandler);
+
+/* core interrupt handlers */
+
+PROVIDE(NonMaskableInt = DefaultHandler);
+PROVIDE(Software = DefaultHandler);
+
+/* external interrupt handlers */
+
+PROVIDE(WWDG = DefaultHandler);
+PROVIDE(PVD = DefaultHandler);
+PROVIDE(TAMPER = DefaultHandler);
+PROVIDE(RTC = DefaultHandler);
+PROVIDE(FLASH = DefaultHandler);
+PROVIDE(RCC = DefaultHandler);
+PROVIDE(EXTI0 = DefaultHandler);
+PROVIDE(EXTI1 = DefaultHandler);
+PROVIDE(EXTI2 = DefaultHandler);
+PROVIDE(EXTI3 = DefaultHandler);
+PROVIDE(EXTI4 = DefaultHandler);
+PROVIDE(DMA1_CHANNEL1 = DefaultHandler);
+PROVIDE(DMA1_CHANNEL2 = DefaultHandler);
+PROVIDE(DMA1_CHANNEL3 = DefaultHandler);
+PROVIDE(DMA1_CHANNEL4 = DefaultHandler);
+PROVIDE(DMA1_CHANNEL5 = DefaultHandler);
+PROVIDE(DMA1_CHANNEL6 = DefaultHandler);
+PROVIDE(DMA1_CHANNEL7 = DefaultHandler);
+PROVIDE(ADC = DefaultHandler);
+PROVIDE(USB_HP_CAN1_TX = DefaultHandler);
+/*PROVIDE(USB_LP_CAN1_RX0 = DefaultHandler);*/
+PROVIDE(CAN1_RX1 = DefaultHandler);
+PROVIDE(CAN1_SCE = DefaultHandler);
+PROVIDE(EXTI9_5 = DefaultHandler);
+PROVIDE(TIM1_BRK = DefaultHandler);
+PROVIDE(TIM1_UP_ = DefaultHandler);
+PROVIDE(TIM1_TRG_COM = DefaultHandler);
+PROVIDE(TIM1_CC = DefaultHandler);
+PROVIDE(TIM2 = DefaultHandler);
+PROVIDE(TIM3 = DefaultHandler);
+PROVIDE(TIM4 = DefaultHandler);
+PROVIDE(I2C1_EV = DefaultHandler);
+PROVIDE(I2C1_ER = DefaultHandler);
+PROVIDE(I2C2_EV = DefaultHandler);
+PROVIDE(I2C2_ER = DefaultHandler);
+PROVIDE(SPI1 = DefaultHandler);
+PROVIDE(SPI2 = DefaultHandler);
+PROVIDE(USART1 = DefaultHandler);
+PROVIDE(USART2 = DefaultHandler);
+PROVIDE(USART3 = DefaultHandler);
+PROVIDE(EXTI15_10 = DefaultHandler);
+PROVIDE(RTCALARM = DefaultHandler);
+PROVIDE(USBWAKE_UP = DefaultHandler);
+PROVIDE(TIM8_BRK = DefaultHandler);
+PROVIDE(TIM8_UP_ = DefaultHandler);
+PROVIDE(TIM8_TRG_COM = DefaultHandler);
+PROVIDE(TIM8_CC = DefaultHandler);
+PROVIDE(RNG = DefaultHandler);
+PROVIDE(FSMC = DefaultHandler);
+PROVIDE(SDIO = DefaultHandler);
+PROVIDE(TIM5 = DefaultHandler);
+PROVIDE(SPI3 = DefaultHandler);
+PROVIDE(UART4 = DefaultHandler);
+PROVIDE(UART5 = DefaultHandler);
+PROVIDE(TIM6 = DefaultHandler);
+PROVIDE(TIM7 = DefaultHandler);
+PROVIDE(DMA2_CHANNEL1 = DefaultHandler);
+PROVIDE(DMA2_CHANNEL2 = DefaultHandler);
+PROVIDE(DMA2_CHANNEL3 = DefaultHandler);
+PROVIDE(DMA2_CHANNEL4 = DefaultHandler);
+PROVIDE(DMA2_CHANNEL5 = DefaultHandler);
+PROVIDE(ETH = DefaultHandler);
+PROVIDE(ETH_WKUP = DefaultHandler);
+PROVIDE(CAN2_TX = DefaultHandler);
+PROVIDE(CAN2_RX0 = DefaultHandler);
+PROVIDE(CAN2_RX1 = DefaultHandler);
+PROVIDE(CAN2_SCE = DefaultHandler);
+PROVIDE(OTG_FS = DefaultHandler);
+PROVIDE(USBHSWAKEUP = DefaultHandler);
+PROVIDE(USBHS = DefaultHandler);
+PROVIDE(DVP = DefaultHandler);
+PROVIDE(UART6 = DefaultHandler);
+PROVIDE(UART7 = DefaultHandler);
+PROVIDE(UART8 = DefaultHandler);
+PROVIDE(TIM9_BRK = DefaultHandler);
+PROVIDE(TIM9_UP_ = DefaultHandler);
+PROVIDE(TIM9_TRG_COM = DefaultHandler);
+PROVIDE(TIM9_CC = DefaultHandler);
+PROVIDE(TIM10_BRK = DefaultHandler);
+PROVIDE(TIM10_UP_ = DefaultHandler);
+PROVIDE(TIM10_TRG_COM = DefaultHandler);
+PROVIDE(TIM10_CC = DefaultHandler);
+PROVIDE(DMA2_CHANNEL6 = DefaultHandler);
+PROVIDE(DMA2_CHANNEL7 = DefaultHandler);
+PROVIDE(DMA2_CHANNEL8 = DefaultHandler);
+PROVIDE(DMA2_CHANNEL9 = DefaultHandler);
+PROVIDE(DMA2_CHANNEL10 = DefaultHandler);
+PROVIDE(DMA2_CHANNEL11 = DefaultHandler);

board/modules/Sensors_can/ch32-sensor/openocd.cfg

@@ -0,0 +1,17 @@
+set _CHIPNAME ch32v203
+set _TARGETNAME $_CHIPNAME.cpu
+
+#bindto 0.0.0.0
+
+adapter driver wlinke
+adapter speed 6000
+transport select sdi
+
+sdi newtap $_CHIPNAME cpu -irlen 5 --expected-id 0x00001
+target create $_TARGETNAME.0 wch_riscv -chain-position $_TARGETNAME
+$_TARGETNAME.0 configure -work-area-phys 0x20000000 -work-area-size 10000 -work-area-backup 1
+set _FLASHNAME $_CHIPNAME.flash
+
+flash bank $_FLASHNAME wch_rsicv 0x00000000 0 0 0 $_TARGETNAME.0
+
+init

board/modules/Sensors_can/ch32-sensor/rust-toolchain.toml

@@ -0,0 +1,2 @@
+[toolchain]
+channel = "nightly"

board/modules/Sensors_can/ch32-sensor/src/main.rs

@@ -0,0 +1,61 @@
+#![no_std]
+#![no_main]
+#![feature(type_alias_impl_trait)]
+#![feature(impl_trait_in_assoc_type)]
+
+// Simple 555-like oscillator implemented in firmware.
+// - Q output: PB2 (also drives the on-board LED if present)
+// - Combined Trigger/Threshold analog input: PA0 (capacitor node)
+// Wiring suggestion:
+//   Q (PB2) --[R]--+-- C -- GND
+//                   |
+//                 PA0 (ADC input)
+// The firmware toggles Q high when PA0 <= 1/3 Vref and low when PA0 >= 2/3 Vref.
+
+use embassy_executor::Spawner;
+use embassy_time::Timer;
+use hal::gpio::{Level, Output};
+use {ch32_hal as hal, panic_halt as _};
+
+use hal::adc::{Adc, SampleTime};
+
+#[embassy_executor::main(entry = "qingke_rt::entry")]
+async fn main(_spawner: Spawner) -> ! {
+    let p = hal::init(Default::default());
+
+    // Q output on PB2
+    let mut q = Output::new(p.PB2, Level::Low, Default::default());
+
+    // ADC on PA0 for combined Trigger/Threshold input
+    let mut adc = Adc::new(p.ADC1, Default::default());
+    let mut trig_thres = p.PA0; // analog-capable pin used as ADC channel
+
+    // ADC characteristics: assume 12-bit if HAL doesn't expose it.
+    // If the HAL provides a method to query resolution, prefer that.
+    let full_scale: u16 = 4095; // 12-bit default
+    let thr_low: u16 = (full_scale as u32 / 3) as u16;        // ~1/3 Vref
+    let thr_high: u16 = ((full_scale as u32 * 2) / 3) as u16; // ~2/3 Vref
+
+    // Start with Q low. State variable to avoid redundant toggles.
+    let mut q_high = false;
+    q.set_low();
+
+    loop {
+        // Read capacitor node voltage via ADC
+        let sample: u16 = adc.convert(&mut trig_thres, SampleTime::CYCLES239_5);
+
+        // Implement Schmitt trigger behavior like NE555 using thresholds
+        if !q_high && sample <= thr_low {
+            // Trigger: voltage fell below 1/3 Vref -> set output high
+            q.set_high();
+            q_high = true;
+        } else if q_high && sample >= thr_high {
+            // Threshold: voltage rose above 2/3 Vref -> set output low
+            q.set_low();
+            q_high = false;
+        }
+
+        // Small delay to reduce CPU usage; adjust for responsiveness/noise
+        Timer::after_micros(200).await;
+    }
+}

board/modules/Sensors_can/ch32-sensor/wch-tools.Containerfile

@@ -0,0 +1,27 @@
+FROM debian:bookworm
+
+RUN apt update -y && apt upgrade -y && apt install git libjaylink-dev libusb-1.0-0 unzip curl libhidapi-hidraw0 xz-utils -y
+
+RUN cd /root && \
+    curl -L -o mrs-toolchain.tar.xz "https://github.com/ch32-riscv-ug/MounRiver_Studio_Community_miror/releases/download/1.92-toolchain/MRS_Toolchain_Linux_x64_V1.92.tar.xz" && \
+    mkdir mrs-toolchain && \
+    tar -xvf mrs-toolchain.tar.xz -C mrs-toolchain --strip-components=1 && \
+    mv mrs-toolchain/OpenOCD/bin/openocd /usr/local/bin && \
+    mv mrs-toolchain/OpenOCD/share/openocd /usr/local/share && \
+    # mv mrs-toolchain/RISC-V_Embedded_GCC12/bin/riscv-none-elf-gdb /usr/local/bin && \                     # both toolchains in MRS are to old to work with emacs dape
+    # mv mrs-toolchain/RISC-V_Embedded_GCC12/libexec /usr/local && \                                        # both toolchains in MRS are to old to work with emacs dape
+    rm -rf mrs-toolchain mrs-toolchain.tar.xz && \
+    # Use up to date xpack toolchains for gdb
+    curl -L -o xpack-riscv-toolchain.tar.gz "https://github.com/xpack-dev-tools/riscv-none-elf-gcc-xpack/releases/download/v14.2.0-3/xpack-riscv-none-elf-gcc-14.2.0-3-linux-x64.tar.gz" && \
+    mkdir xpack-toolchain && \
+    tar -xvf xpack-riscv-toolchain.tar.gz -C xpack-toolchain --strip-components=1 && \
+    mv xpack-toolchain/bin/* /usr/local/bin && \
+    mv xpack-toolchain/lib/ /usr/local && \
+    mv xpack-toolchain/lib64/ /usr/local && \
+    mv xpack-toolchain/libexec /usr/local && \
+    mv xpack-toolchain/riscv-none-elf /usr/local && \
+    rm -rf xpack-toolchain xpack-riscv-toolchain.tar.gz
+
+RUN mkdir -p /root/.config/gdb && echo "set auto-load safe-path /" >> /root/.config/gdb/gdbinit
+
+ENTRYPOINT [ "/usr/bin/bash" ]

board/modules/Sensors_simplified/Sensors/fp-lib-table

@@ -0,0 +1,4 @@
+(fp_lib_table
+  (version 7)
+  (lib (name "Sensor")(type "KiCad")(uri "${KIPRJMOD}/Sensor.pretty")(options "")(descr ""))
+)

rust/src/config.rs

@@ -58,7 +58,7 @@ pub struct TankConfig {
     pub tank_warn_percent: u8,
     pub tank_empty_percent: u8,
     pub tank_full_percent: u8,
-    pub ml_per_pulse: f32
+    pub ml_per_pulse: f32,
 }
 impl Default for TankConfig {
     fn default() -> Self {
@@ -111,6 +111,7 @@ pub struct PlantControllerConfig {
 pub struct PlantConfig {
     pub mode: PlantWateringMode,
     pub target_moisture: f32,
+    pub min_moisture: f32,
     pub pump_time_s: u16,
     pub pump_limit_ml: u16,
     pub pump_cooldown_min: u16,
@@ -131,6 +132,7 @@ impl Default for PlantConfig {
         Self {
             mode: PlantWateringMode::OFF,
             target_moisture: 40.,
+            min_moisture: 30.,
             pump_time_s: 30,
             pump_limit_ml: 5000,
             pump_cooldown_min: 60,

rust/src/hal/mod.rs

@@ -23,6 +23,7 @@ use bq34z100::Bq34z100g1Driver;
 use ds323x::{DateTimeAccess, Ds323x};
 use eeprom24x::{Eeprom24x, SlaveAddr, Storage};
 use embedded_hal_bus::i2c::MutexDevice;
+use esp_idf_hal::pcnt::PCNT1;
 use esp_idf_hal::{
     adc::ADC1,
     delay::Delay,
@@ -54,7 +55,6 @@ use esp_idf_hal::pcnt::PCNT1;
 //Only support for 8 right now!
 pub const PLANT_COUNT: usize = 8;
 
-
 const TANK_MULTI_SAMPLE: usize = 11;
 
 pub static I2C_DRIVER: Lazy<Mutex<I2cDriver<'static>>> = Lazy::new(PlantHal::create_i2c);

rust/src/hal/v3_hal.rs

@@ -136,7 +136,7 @@ pub(crate) fn create_v3(
         peripherals.gpio5,
         tank_power_pin,
         flow_sensor_pin,
-        peripherals.pcnt1
+        peripherals.pcnt1,
     )?;
 
     let mut signal_counter = PcntDriver::new(

rust/src/hal/v4_hal.rs

@@ -159,7 +159,7 @@ pub(crate) fn create_v4(
         peripherals.gpio5,
         tank_power_pin,
         flow_sensor_pin,
-        peripherals.pcnt1
+        peripherals.pcnt1,
     )?;
 
     let mut sensor_expander = Pca9535Immediate::new(MutexDevice::new(&I2C_DRIVER), 34);

rust/src/hal/water.rs

@@ -6,7 +6,9 @@ use esp_idf_hal::adc::oneshot::{AdcChannelDriver, AdcDriver};
 use esp_idf_hal::adc::{attenuation, Resolution, ADC1};
 use esp_idf_hal::delay::Delay;
 use esp_idf_hal::gpio::{AnyIOPin, AnyInputPin, Gpio5, InputOutput, PinDriver, Pull};
-use esp_idf_hal::pcnt::{PcntChannel, PcntChannelConfig, PcntControlMode, PcntCountMode, PcntDriver, PinIndex, PCNT1};
+use esp_idf_hal::pcnt::{
+    PcntChannel, PcntChannelConfig, PcntControlMode, PcntCountMode, PcntDriver, PinIndex, PCNT1,
+};
 use esp_idf_sys::EspError;
 use one_wire_bus::OneWire;
 
@@ -25,7 +27,7 @@ impl<'a> TankSensor<'a> {
         gpio5: Gpio5,
         tank_power_pin: AnyIOPin,
         flow_sensor_pin: AnyIOPin,
-        pcnt1: PCNT1
+        pcnt1: PCNT1,
     ) -> anyhow::Result<TankSensor<'a>> {
         let mut one_wire_pin =
             PinDriver::input_output_od(one_wire_pin).expect("Failed to configure pin");
@@ -73,7 +75,6 @@ impl<'a> TankSensor<'a> {
             },
         )?;
 
-
         Ok(TankSensor {
             one_wire_bus,
             tank_channel,

rust/src/main.rs

@@ -591,16 +591,31 @@ pub fn do_secure_pump(
     let mut first_error = true;
     let mut pump_time_s = 0;
     if !dry_run {
-        board.board_hal.get_tank_sensor().unwrap().reset_flow_meter();
+        board
-        board.board_hal.get_tank_sensor().unwrap().start_flow_meter();
+            .board_hal
+            .get_tank_sensor()
+            .unwrap()
+            .reset_flow_meter();
+        board
+            .board_hal
+            .get_tank_sensor()
+            .unwrap()
+            .start_flow_meter();
         board.board_hal.pump(plant_id, true)?;
         Delay::new_default().delay_ms(10);
         for step in 0..plant_config.pump_time_s as usize {
-            let flow_value = board.board_hal.get_tank_sensor().unwrap().get_flow_meter_value();
+            let flow_value = board
+                .board_hal
+                .get_tank_sensor()
+                .unwrap()
+                .get_flow_meter_value();
             flow_collector[step] = flow_value;
             let flow_value_ml = flow_value as f32 * board.board_hal.get_config().tank.ml_per_pulse;
 
-            println!("Flow value is {} ml, limit is {} ml raw sensor {}", flow_value_ml, plant_config.pump_limit_ml, flow_value);
+            println!(
+                "Flow value is {} ml, limit is {} ml raw sensor {}",
+                flow_value_ml, plant_config.pump_limit_ml, flow_value
+            );
             if flow_value_ml > plant_config.pump_limit_ml as f32 {
                 println!("Flow value is reached, stopping");
                 break;
@@ -672,9 +687,16 @@ pub fn do_secure_pump(
         }
     }
     board.board_hal.get_tank_sensor().unwrap().stop_flow_meter();
-    let final_flow_value = board.board_hal.get_tank_sensor().unwrap().get_flow_meter_value();
+    let final_flow_value = board
+        .board_hal
+        .get_tank_sensor()
+        .unwrap()
+        .get_flow_meter_value();
     let flow_value_ml = final_flow_value as f32 * board.board_hal.get_config().tank.ml_per_pulse;
-    println!("Final flow value is {} with {} ml", final_flow_value, flow_value_ml);
+    println!(
+        "Final flow value is {} with {} ml",
+        final_flow_value, flow_value_ml
+    );
     current_collector.sort();
     Ok(PumpResult {
         median_current_ma: current_collector[current_collector.len() / 2],

rust/src/plant_state.rs

@@ -78,6 +78,7 @@ impl PumpState {
 pub enum PlantWateringMode {
     OFF,
     TargetMoisture,
+    MinMoisture,
     TimerOnly,
 }
 
@@ -235,6 +236,30 @@ impl PlantState {
                     false
                 }
             }
+            PlantWateringMode::MinMoisture => {
+                let (moisture_percent, _) = self.plant_moisture();
+                if let Some(moisture_percent) = moisture_percent {
+                    if self.pump_in_timeout(plant_conf, current_time) {
+                        false
+                    } else if !in_time_range(
+                        current_time,
+                        plant_conf.pump_hour_start,
+                        plant_conf.pump_hour_end,
+                    ) {
+                        false
+                    } else if (true) {
+                        //if not cooldown min and below max
+                        true
+                    } else if (true) {
+                        //if below min disable cooldown min
+                        true
+                    } else {
+                        false
+                    }
+                } else {
+                    false
+                }
+            }
             PlantWateringMode::TimerOnly => !self.pump_in_timeout(plant_conf, current_time),
         }
     }
@@ -268,7 +293,9 @@ impl PlantState {
                 .map(|t| t.with_timezone(&current_time.timezone())),
             next_pump: if matches!(
                 plant_conf.mode,
-                PlantWateringMode::TimerOnly | PlantWateringMode::TargetMoisture
+                PlantWateringMode::TimerOnly
+                    | PlantWateringMode::TargetMoisture
+                    | PlantWateringMode::MinMoisture
             ) {
                 self.pump.previous_pump.and_then(|last_pump| {
                     last_pump

rust/src_webpack/src/api.ts

@@ -105,6 +105,7 @@ export interface PlantControllerConfig {
 export interface PlantConfig {
     mode: string,
     target_moisture: number,
+    min_moisture: number,
     pump_time_s: number,
     pump_cooldown_min: number,
     pump_hour_start: number,

rust/src_webpack/src/plant.html

@@ -55,6 +55,7 @@
         <select class="plantvalue" id="plant_${plantId}_mode">
             <option value="OFF">Off</option>
             <option value="TargetMoisture">Target</option>
+            <option value="MinMoisture">Min Moisture</option>
             <option value="TimerOnly">Timer</option>
         </select>
 
@@ -63,6 +64,10 @@
         <div class="plantkey">Target Moisture:</div>
         <input class="plantvalue" id="plant_${plantId}_target_moisture" type="number" min="0" max="100" placeholder="0">
     </div>
+    <div class="flexcontainer plantMinEnabledOnly_${plantId}">
+        <div class="plantkey">Minimum Moisture:</div>
+        <input class="plantvalue" id="plant_${plantId}_min_moisture" type="number" min="0" max="100" placeholder="0">
+    </div>
     <div class="flexcontainer plantPumpEnabledOnly_${plantId}">
         <div class="plantkey">Pump Time (s):</div>
         <input class="plantvalue" id="plant_${plantId}_pump_time_s" type="number" min="0" max="600" placeholder="30">

rust/src_webpack/src/plant.ts

@@ -59,6 +59,7 @@ export class PlantView {
     private readonly header: HTMLElement;
     private readonly testButton: HTMLButtonElement;
     private readonly targetMoisture: HTMLInputElement;
+    private readonly minMoisture: HTMLInputElement;
     private readonly pumpTimeS: HTMLInputElement;
     private readonly pumpCooldown: HTMLInputElement;
     private readonly pumpHourStart: HTMLSelectElement;
@@ -118,6 +119,11 @@ export class PlantView {
             controller.configChanged()
         }
 
+        this.minMoisture = document.getElementById("plant_" + plantId + "_min_moisture")! as HTMLInputElement;
+        this.minMoisture.onchange = function () {
+            controller.configChanged()
+        }
+
         this.pumpTimeS = document.getElementById("plant_" + plantId + "_pump_time_s") as HTMLInputElement;
         this.pumpTimeS.onchange = function () {
             controller.configChanged()
@@ -203,13 +209,15 @@ export class PlantView {
         let sensorOnly = document.getElementsByClassName("plantSensorEnabledOnly_"+ this.plantId)
         let pumpOnly = document.getElementsByClassName("plantPumpEnabledOnly_"+ this.plantId)
         let targetOnly = document.getElementsByClassName("plantTargetEnabledOnly_"+ this.plantId)
+        let minOnly = document.getElementsByClassName("plantMinEnabledOnly_"+ this.plantId)
 
         console.log("updateVisibility plantConfig: " + plantConfig.mode)
         let showSensor = plantConfig.sensor_a || plantConfig.sensor_b
         let showPump = plantConfig.mode !== "OFF"
         let showTarget = plantConfig.mode === "TargetMoisture"
+        let showMin = plantConfig.mode === "MinMoisture"
 
-        console.log("updateVisibility showsensor: " + showSensor + " pump " + showPump + " target " +showTarget)
+        console.log("updateVisibility showsensor: " + showSensor + " pump " + showPump + " target " +showTarget + " min " + showMin)
 
         for (const element of Array.from(sensorOnly)) {
             if (showSensor) {
@@ -234,6 +242,14 @@ export class PlantView {
                 element.classList.add("plantHidden_" + this.plantId)
             }
         }
+
+        for (const element of Array.from(minOnly)) {
+            if (showMin) {
+                element.classList.remove("plantHidden_" + this.plantId)
+            } else {
+                element.classList.add("plantHidden_" + this.plantId)
+            }
+        }
     }
 
     setTestResult(result: PumpTestResult) {
@@ -255,6 +271,7 @@ export class PlantView {
     setConfig(plantConfig: PlantConfig) {
         this.mode.value = plantConfig.mode;
         this.targetMoisture.value = plantConfig.target_moisture.toString();
+        this.minMoisture.value = plantConfig.min_moisture?.toString() || "";
         this.pumpTimeS.value = plantConfig.pump_time_s.toString();
         this.pumpCooldown.value = plantConfig.pump_cooldown_min.toString();
         this.pumpHourStart.value = plantConfig.pump_hour_start.toString();
@@ -280,6 +297,7 @@ export class PlantView {
         let conv: PlantConfig =  {
             mode: this.mode.value,
             target_moisture: this.targetMoisture.valueAsNumber,
+            min_moisture: this.minMoisture.valueAsNumber,
             pump_time_s: this.pumpTimeS.valueAsNumber,
             pump_cooldown_min: this.pumpCooldown.valueAsNumber,
             pump_hour_start: +this.pumpHourStart.value,