proceeed further

rust/Cargo.toml

@@ -50,6 +50,7 @@ paste = "1.0.14"
 embedded-hal = "0.2.7"
 dummy-pin = "0.1.1"
 shift-register-driver = "0.1.1"
+one-wire-bus = "0.1.1"
 #?bq34z100 required
 
 

rust/src/main.rs

@@ -1,17 +1,34 @@
-use chrono::Utc;
+
+use std::sync::{Mutex, Arc};
+
+use chrono::{Utc, NaiveDateTime, DateTime};
+
+use ds18b20::Ds18b20;
 use embedded_hal::digital::v1_compat::OldOutputPin;
+use embedded_hal::digital::v2::OutputPin;
 use esp_idf_hal::adc::config::Config;
 use esp_idf_hal::adc::{AdcDriver, AdcChannelDriver, attenuation};
+use esp_idf_hal::delay::Delay;
 use esp_idf_hal::reset::ResetReason;
-use shift_register_driver::sipo::{ShiftRegister24, ShiftRegisterPin};
+use esp_idf_sys::EspError;
-use esp_idf_hal::gpio::PinDriver;
+use one_wire_bus::OneWire;
+use shift_register_driver::sipo::ShiftRegister24;
+use esp_idf_hal::gpio::{PinDriver, Gpio39, Gpio4};
 use esp_idf_hal::prelude::Peripherals;
 
 const PLANT_COUNT:usize = 8;
+const PINS_PER_PLANT:usize = 5;
+const PLANT_PUMP_OFFSET:usize = 0;
+const PLANT_FAULT_OFFSET:usize = 1;
+const PLANT_MOIST_PUMP_OFFSET:usize = 2;
+const PLANT_MOIST_B_OFFSET:usize = 3;
+const PLANT_MOIST_A_OFFSET:usize = 4;
+
+
 #[link_section = ".rtc.data"]
-static mut LAST_WATERING_TIMESTAMP: [u64; PLANT_COUNT] = [0; PLANT_COUNT];
+static mut LAST_WATERING_TIMESTAMP: [i64; PLANT_COUNT] = [0; PLANT_COUNT];
 #[link_section = ".rtc.data"]
-static mut CONSECUTIVE_WATERING_PLANT: [u64; PLANT_COUNT] = [0; PLANT_COUNT];
+static mut CONSECUTIVE_WATERING_PLANT: [u32; PLANT_COUNT] = [0; PLANT_COUNT];
 #[link_section = ".rtc.data"]
 static mut LOW_VOLTAGE_DETECTED:bool = false;
 
@@ -31,147 +48,203 @@ struct BatteryState {
     state_health_percent: u8
 }
 trait PlantCtrlBoardInteraction{
-    fn battery_state(&self,) -> BatteryState;
+    fn battery_state(&mut self,) -> BatteryState;
     
     fn is_day(&self,) -> bool;
-    fn water_temperature_c(&self,) -> u16;
+    fn water_temperature_c(&mut self,) -> Option<f32>;
-    fn tank_sensor_mv(&self,) -> u16;
+    fn tank_sensor_mv(&mut self,) -> u16;
 
-    fn set_low_voltage_in_cycle(&self,);
+    fn set_low_voltage_in_cycle(&mut self,);
-    fn clear_low_voltage_in_cycle(&self,);
+    fn clear_low_voltage_in_cycle(&mut self,);
-    fn low_voltage_in_cycle(&self) -> bool;
+    fn low_voltage_in_cycle(&mut self) -> bool;
-    fn any_pump(&self, enabled:bool);
+    fn any_pump(&mut self, enabled:bool);
 
     //keep state during deepsleep
     fn light(&self,enable:bool);
 
-    fn plant_count(&self,) -> i8;
+    fn plant_count(&self,) -> usize;
-    fn measure_moisture_b_hz(&self,plant:i8) -> i16;
+    fn measure_moisture_b_hz(&self,plant:usize) -> i16;
-    fn measure_moisture_a_hz(&self,plant:i8) -> i16;
+    fn measure_moisture_a_hz(&self,plant:usize) -> i16;
-    fn measure_moisture_p_hz(&self,plant:i8) -> i16;
+    fn measure_moisture_p_hz(&self,plant:usize) -> i16;
-    fn pump(&self,plant:i8, enable:bool);
+    fn pump(&self,plant:usize, enable:bool);
-    fn last_pump_time(&self,plant:i8) -> chrono::DateTime<Utc>;
+    fn last_pump_time(&self,plant:usize) -> chrono::DateTime<Utc>;
-    fn store_last_pump_time(&self,plant:i8, time: chrono::DateTime<Utc>);
+    fn store_last_pump_time(&mut self,plant:usize, time: chrono::DateTime<Utc>);
-    fn store_consecutive_pump_count(&self,plant:i8, count:i16);
+    fn store_consecutive_pump_count(&mut self,plant:usize, count:u32);
-    fn consecutive_pump_count(&self,plant:i8) -> i16;
+    fn consecutive_pump_count(&mut self,plant:usize) -> u32;
 
     //keep state during deepsleep
-    fn fault(&self,plant:i8, enable:bool);
+    fn fault(&self,plant:usize, enable:bool);
     
     fn default() -> Self;
 }
 
-trait Plant{
-    fn setPump(pump:bool);
-    
 
+struct PlantCtrlBoard<'a>{
+    shift_register: ShiftRegister24<OldOutputPin<PinDriver<'a, esp_idf_hal::gpio::Gpio21, esp_idf_hal::gpio::Output>>, OldOutputPin<PinDriver<'a, esp_idf_hal::gpio::Gpio22, esp_idf_hal::gpio::Output>>, OldOutputPin<PinDriver<'a, esp_idf_hal::gpio::Gpio19, esp_idf_hal::gpio::Output>>>,
+    consecutive_watering_plant: Mutex<[u32; PLANT_COUNT]>,
+    last_watering_timestamp: Mutex<[i64; PLANT_COUNT]>,
+    low_voltage_detected: Mutex<bool>,
+    tank_driver: AdcDriver<'a, esp_idf_hal::adc::ADC1>,
+    tank_channel: esp_idf_hal::adc::AdcChannelDriver<'a, { attenuation::DB_11 }, Gpio39 >,
+    solar_is_day: PinDriver<'a, esp_idf_hal::gpio::Gpio25, esp_idf_hal::gpio::Input>,
+    water_temp_sensor: Option<Ds18b20>,
+    one_wire_bus: OneWire<PinDriver<'a, Gpio4, esp_idf_hal::gpio::InputOutput>>
 }
 
-struct PlantHal<'d>{
+impl PlantCtrlBoardInteraction for PlantCtrlBoard<'_> {
-    pump:ShiftRegisterPin<'d>
-}
-
-struct PlantCtrlBoard{
-    dummy:i32
-}
-
-impl PlantCtrlBoardInteraction for PlantCtrlBoard {
     fn default() -> Self {
         let peripherals = Peripherals::take().unwrap(); 
         
-        let mut adc = AdcDriver::new(peripherals.adc1, &Config::new().calibration(true)).unwrap();
-        let mut adc_pin: esp_idf_hal::adc::AdcChannelDriver<{ attenuation::DB_11 }, _> = AdcChannelDriver::new(peripherals.pins.gpio39).unwrap();
-        let analog_value = adc.read(&mut adc_pin);
-        
         let clock = OldOutputPin::from(PinDriver::output(peripherals.pins.gpio21).unwrap());
         let latch = OldOutputPin::from(PinDriver::output(peripherals.pins.gpio22).unwrap());
         let data = OldOutputPin::from(PinDriver::output(peripherals.pins.gpio19).unwrap());
 
 
-        let shift_register = ShiftRegister24::new(clock, latch, data);
+        let one_wire_pin = PinDriver::input_output_od(peripherals.pins.gpio4).unwrap();
-        let registerOutput = shift_register.decompose();
 
+        let mut one_wire_bus: OneWire<PinDriver<'_, Gpio4, esp_idf_hal::gpio::InputOutput>> = OneWire::new(one_wire_pin).unwrap();
+        let mut delay = Delay::new_default();
 
-
+        if one_wire_bus.reset(&mut delay).is_err() {
-        Self { dummy: 12 }
+            //TODO check a lot of one wire error conditions here
         }
 
-    fn battery_state(&self,) -> BatteryState {
+        let device_address = one_wire_bus.devices(false, &mut delay).next().unwrap().unwrap();
+        let water_temp_sensor: Option<Ds18b20> = Ds18b20::new::<EspError>(device_address).ok();
+        //TODO make to none if not possible to init
+
+        //init,reset rtc memory depending on cause
+        let reasons = ResetReason::get();
+        let reset_store = match reasons {
+            ResetReason::Software => false,
+            ResetReason::ExternalPin => false,
+            ResetReason::Watchdog => true,
+            ResetReason::Sdio => true,
+            ResetReason::Panic => true,
+            ResetReason::InterruptWatchdog => true,
+            ResetReason::PowerOn => true,
+            ResetReason::Unknown => true,
+            ResetReason::Brownout => true,
+            ResetReason::TaskWatchdog => true,
+            ResetReason::DeepSleep => false,
+        };
+        if reset_store {
+            println!("Clear and reinit RTC store");
+            unsafe {
+                LAST_WATERING_TIMESTAMP = [0; PLANT_COUNT];
+                CONSECUTIVE_WATERING_PLANT = [0; PLANT_COUNT];
+                LOW_VOLTAGE_DETECTED = false;
+            };
+        } else {
+            println!("Keeping RTC store");
+        }
+
+        Self { 
+            shift_register : ShiftRegister24::new(clock, latch, data),
+            last_watering_timestamp : Mutex::new(unsafe { LAST_WATERING_TIMESTAMP }),
+            consecutive_watering_plant : Mutex::new(unsafe { CONSECUTIVE_WATERING_PLANT }),
+            low_voltage_detected : Mutex::new(unsafe { LOW_VOLTAGE_DETECTED }),
+            tank_driver : AdcDriver::new(peripherals.adc1, &Config::new().calibration(true)).unwrap(),
+            tank_channel: AdcChannelDriver::new(peripherals.pins.gpio39).unwrap(),
+            solar_is_day : PinDriver::input(peripherals.pins.gpio25).unwrap(),
+            water_temp_sensor : water_temp_sensor,
+            one_wire_bus: one_wire_bus,
+        }
+    }
+
+    fn battery_state(&mut self,) -> BatteryState {
         todo!()
     }
 
     fn is_day(&self,) -> bool {
-        todo!()
+        return self.solar_is_day.get_level().into();
     }
 
-    fn water_temperature_c(&self,) -> u16 {
+    fn water_temperature_c(&mut self,) -> Option<f32> {
-        todo!()
+        return match &self.water_temp_sensor{
+            Some(sensor) => {
+                let mut delay = Delay::new_default();
+                sensor.start_temp_measurement(&mut self.one_wire_bus, &mut delay);
+                ds18b20::Resolution::Bits12.delay_for_measurement_time(&mut delay);    
+                let sensor_data  = sensor.read_data(&mut self.one_wire_bus, &mut delay).unwrap();
+                println!("Water Temp is {}°C", sensor_data.temperature);
+                if sensor_data.temperature == 85_f32 {
+                    return Option::None;
+                } else {
+                    Some(sensor_data.temperature)
                 }
-
+            },
-    fn tank_sensor_mv(&self,) -> u16 {
+            None => Option::None,
-        todo!()
-    }
-
-    fn set_low_voltage_in_cycle(&self,) {
-        unsafe {
-            LOW_VOLTAGE_DETECTED = true;
         }
     }
 
-    fn clear_low_voltage_in_cycle(&self,) {
+    fn tank_sensor_mv(&mut self,) -> u16 {
-        unsafe {
+        return self.tank_driver.read(&mut self.tank_channel).unwrap();
-            LOW_VOLTAGE_DETECTED = false;
     }
+
+    fn set_low_voltage_in_cycle(&mut self,) {
+        *self.low_voltage_detected.get_mut().unwrap() = true;
+    }
+
+    fn clear_low_voltage_in_cycle(&mut self,) {
+        *self.low_voltage_detected.get_mut().unwrap() = false;
     }
 
     fn light(&self,enable:bool) {
         todo!()
     }
 
-    fn plant_count(&self,) -> i8 {
+    fn plant_count(&self,) -> usize {
+        PLANT_COUNT
+    }
+
+    fn measure_moisture_b_hz(&self,plant:usize) -> i16 {
         todo!()
     }
 
-    fn measure_moisture_b_hz(&self,plant:i8) -> i16 {
+    fn measure_moisture_a_hz(&self,plant:usize) -> i16 {
         todo!()
     }
 
-    fn measure_moisture_a_hz(&self,plant:i8) -> i16 {
+    fn measure_moisture_p_hz(&self,plant:usize) -> i16 {
         todo!()
     }
 
-    fn measure_moisture_p_hz(&self,plant:i8) -> i16 {
+    fn pump(&self,plant:usize, enable:bool) {
-        todo!()
+        let index = plant*PINS_PER_PLANT*PLANT_PUMP_OFFSET;
+        self.shift_register.decompose()[index].set_state(enable.into()).unwrap()
     }
 
-    fn pump(&self,plant:i8, enable:bool) {
+    fn last_pump_time(&self,plant:usize) -> chrono::DateTime<Utc> {
-        todo!()
+        let ts = unsafe { LAST_WATERING_TIMESTAMP }[plant];
+        let timestamp = NaiveDateTime::from_timestamp_millis(ts).unwrap();
+        return DateTime::<Utc>::from_naive_utc_and_offset(timestamp, Utc);
     }
 
-    fn last_pump_time(&self,plant:i8) -> chrono::DateTime<Utc> {
+    fn store_last_pump_time(&mut self,plant:usize, time: chrono::DateTime<Utc>) {
-        todo!()
+        self.last_watering_timestamp.get_mut().unwrap()[plant] = time.timestamp_millis();
     }
 
-    fn store_last_pump_time(&self,plant:i8, time: chrono::DateTime<Utc>) {
+    fn store_consecutive_pump_count(&mut self,plant:usize, count:u32) {
-        todo!()
+        self.consecutive_watering_plant.get_mut().unwrap()[plant] = count;
     }
 
-    fn store_consecutive_pump_count(&self,plant:i8, count:i16) {
+    fn consecutive_pump_count(&mut self,plant:usize) -> u32 {
-        todo!()
+        return self.consecutive_watering_plant.get_mut().unwrap()[plant]
     }
 
-    fn consecutive_pump_count(&self,plant:i8) -> i16 {
+    fn fault(&self,plant:usize, enable:bool) {
-        todo!()
+        let index = plant*PINS_PER_PLANT*PLANT_FAULT_OFFSET;
+        self.shift_register.decompose()[index].set_state(enable.into()).unwrap()
     }
 
-    fn fault(&self,plant:i8, enable:bool) {
+    fn low_voltage_in_cycle(&mut self) -> bool {
-        todo!()
+        return *self.low_voltage_detected.get_mut().unwrap()
     }
 
-    fn low_voltage_in_cycle(&self) -> bool {
+    fn any_pump(&mut self, enabled:bool) {
-        unsafe {
+
-            return LOW_VOLTAGE_DETECTED;
+        todo!()
-        }
     }
 
 
@@ -194,16 +267,18 @@ fn main() {
     log::info!("Hello, world!");
 
 
-    let reasons = ResetReason::get();
-    //init,reset rtc memory depending on cause
 
     let board = PlantCtrlBoard::default();
 
+
     //check if we know the time current > 2020
         //if failed assume its 1.1.1970 
             //12:00 if solar reports day
             //00:00 if solar repors night
     
+    //continous/interrupt?
+        //check if boot button is pressed, if longer than 5s delete config and reboot into config mode
+
     //check if we have a config file
         // if not found or parsing error -> error very fast blink general fault
             //if this happens after a firmeware upgrade (check image state), mark as invalid
@@ -224,16 +299,49 @@ fn main() {
             //if no mqtt, set general fault persistent
 
     //measure each plant moisture
-    //check which plants need to be watered 
+
-        //()
+    //if config battery mode
+        //read battery level
+            //if not possible set general fault persistent, but do continue
+    //else
+        //assume 12v and max capacity
 
     //if tank sensor is enabled
         //if tank sensor fault abort if config require is set
         //check if water is > minimum allowed || fault
             //if not, set all plants requiring water to persistent fault
-        // pump water for first plant update last water timestamp
+
-        // wait for config time per plant
+    //for each plant
-        //
+        //check if moisture is < target
+            //state  += dry
+            //check if in cooldown
+                //state += cooldown
+                //check if consecutive pumps > limit
+                    //state += notworking
+                    //set plant fault persistent
+            
+            //pump one cycle
+            // set last pump time to now
+                //during pump state += active
+            //after pump check if Pump moisture value is increased by config delta x
+                // state -= active
+                // state += cooldown
+                // if not set plant error persistent fault    
+                // state += notworking
+            //set consecutive pumps+=1
+    
+
+    //check if during light time
+        //lightstate += out of worktime
+    //check battery level
+        //lightstate += battery empty
+    //check solar level if config requires
+        //lightstate += stillday
+    //if no preventing lightstate, enable light
+        //lightstate = active
+    
+        
+        
 
 
 

rust/src/second.rs

@@ -0,0 +1,63 @@
+use anyhow::{Context, Error};
+use esp_idf_hal::gpio::AnyInputPin;
+use esp_idf_hal::pcnt::{PcntChannel, PcntChannelConfig, PcntControlMode, PcntCountMode, PcntDriver, PinIndex};
+use esp_idf_hal::peripherals::Peripherals;
+
+#[link_section = ".rtc.data"]
+static mut MY_FANCY_VARIABLE: u32 = 0;
+
+
+fn read_moisture() -> Result<i16,Error> {
+
+    let p = Peripherals::take().unwrap();
+
+    let counter1 = p.pcnt0;
+    let mut counter_unit1 = PcntDriver::new(
+        counter1,
+        Some(p.pins.gpio19),
+        Option::<AnyInputPin>::None,
+        Option::<AnyInputPin>::None,
+        Option::<AnyInputPin>::None,
+    ).context("Could not obtain counter unit")?;
+
+    counter_unit1.channel_config(
+        PcntChannel::Channel0,
+        PinIndex::Pin0,
+        PinIndex::Pin1,
+        &PcntChannelConfig {
+            lctrl_mode: PcntControlMode::Reverse,
+            hctrl_mode: PcntControlMode::Keep,
+            pos_mode: PcntCountMode::Decrement,
+            neg_mode: PcntCountMode::Increment,
+            counter_h_lim: i16::MAX,
+            counter_l_lim: 0,
+        },
+    ).context("Failed to configure pulse counter")?;
+
+    counter_unit1.set_filter_value(u16::min(10 * 80, 1023))?;
+    counter_unit1.filter_enable().context("Failed to enable pulse counter filter")?;
+
+    counter_unit1.counter_pause().context("Failed to pause pulse counter")?;
+    counter_unit1.counter_clear().context("Failed to clear pulse counter")?;
+    counter_unit1.counter_resume().context("Failed to start pulse counter")?;
+
+    let measurement = 100;
+    let waitFor = 1000/100;
+    //delay(measurement);
+
+    counter_unit1.counter_pause().context("Failed to end pulse counter measurement")?;
+    return Ok(counter_unit1.get_counter_value().context("Failed to read pulse counter value")?*waitFor);
+}
+fn main() {
+    // It is necessary to call this function once. Otherwise some patches to the runtime
+    // implemented by esp-idf-sys might not link properly. See https://github.com/esp-rs/esp-idf-template/issues/71
+    esp_idf_svc::sys::link_patches();
+
+    // Bind the log crate to the ESP Logging facilities
+    esp_idf_svc::log::EspLogger::initialize_default();
+
+    log::info!("Hello, world!");
+
+
+
+}