/**
 * @file ControllerConfiguration.h
 * @author your name (you@domain.com)
 * @brief 
 * @version 0.1
 * @date 2020-05-30
 * 
 * @copyright Copyright (c) 2020
 * 
 * \mainpage Configuration of the controller
 * @{
 * Describe the used PINs of the controller
 *  
 * @subpage Controller
 * 
 * @subpage Homie
 * 
 * @subpage Configuration
 * 
 * There are several modes in the controller
 * \dot
 *  digraph Operationmode {
 *      ranksep=.75;
 *      poweroff [ label="off" ];
 *      mode1 [ label="Mode 1 - Sensor only", shape=box, width=2 ];
 *      mode2 [ label="Mode 2 - Wifi enabled", shape=box ];
 *      mode3 [ label="Mode 3 - Stay alive", shape=box ];
 *      mode1 -> mode2 [ label="wakeup reason", fontsize=10 ];
 *      mode1 -> mode2 [ label="Time duration", fontsize=10 ];
 *      mode2 -> mode3 [ label="Over the Air Update", fontsize=10 ];
 *      mode3 -> mode2 [ label="Over the Air Finished", fontsize=10 ];
 *      mode3 -> mode2 [ label="Mqtt Command", fontsize=10 ];
 *      mode2 -> mode3 [ label="Mqtt Command", fontsize=10 ];
 *      poweroff -> mode1 [ label="deep sleep wakeup", fontsize=10 ];
 *      mode1 -> poweroff [ label="enter deep sleep", fontsize=10 ];
 *      mode2 -> poweroff [ label="Mqtt queue empty", fontsize=10 ];
 *  }
 *  \enddot
 * 
 * Before entering Deep sleep the controller is configured with an wakeup time.
 * 
 * @}
 */
#ifndef CONTROLLER_CONFIG_H
#define CONTROLLER_CONFIG_H
/** \addtogroup GPIO Settings
 *  @{
 */
#define SENSOR_PLANT0 32 /**< GPIO 32 (ADC1) */
#define SENSOR_PLANT1 33 /**< GPIO 33 (ADC1) */
#define SENSOR_PLANT2 25 /**< GPIO 25 (ADC2) */
#define SENSOR_PLANT3 26 /**< GPIO 26 (ADC2) */
#define SENSOR_PLANT4 27 /**< GPIO 27 (ADC2) */
#define SENSOR_PLANT5 39 /**< SENSOR_VIN */
#define SENSOR_PLANT6 36 /**< SENSOR_VP  */

#define OUTPUT_PUMP0 15 /**< GPIO 15 */
#define OUTPUT_PUMP1 5  /**< GPIO 5 */
#define OUTPUT_PUMP2 18 /**< GPIO 18 */
#define OUTPUT_PUMP3 19 /**< GPIO 19 */
#define OUTPUT_PUMP4 21 /**< GPIO 21 */
#define OUTPUT_PUMP5 22 /**< GPIO 22  */
#define OUTPUT_PUMP6 23 /**< GPIO 23 */

#define OUTPUT_ENABLE_SENSOR 14 /**< GPIO 14 - Enable Sensors  */
#define OUTPUT_ENABLE_PUMP   13 /**< GPIO 13 - Enable Pumps  */

#define SENSOR_ONEWIRE      12 /**< GPIO 12 - Temperatur sensor, Battery and other cool onewire stuff */
#define SENSOR_TANK_ECHO    16 /**< GPIO 16 - echo feedback of water sensor */ 
#define SENSOR_TANK_TRG     17 /**< GPIO 17 - trigger for water sensor */
#define BUTTON              0  /**< GPIO 0 - Fix button of NodeMCU */
#define CUSTOM1_PIN3        2   /**< GPIO 2 - Custom GPIO controlling a MOSFET, connected to GND */
#define CUSTOM1_PIN2        4   /**< GPIO 4 - custom GPIO directly connected to GPIO header */
#define I2C1_PIN2          34   /**< GPIO 34 - I2C */
#define I2C1_PIN3          35   /**< GPIO 35 - I2C */
/* @} */

/** \addtogroup Configuration
 *  @{
 */
#define FIRMWARE_VERSION "1.1.0"

#define MOIST_SENSOR_MAX_ADC                (85 * 4095 / 100)
#define MOIST_SENSOR_MIN_ADC                (25 * 4095 / 100)

#define SOLAR_VOLT_FACTOR           2
#define BATTSENSOR_INDEX_SOLAR      0
#define BATTSENSOR_INDEX_BATTERY    1

#define MQTT_TIMEOUT                (1000 * 10) /**< After 10 seconds, MQTT is expected to be connected */

#define MAX_PLANTS          7
#define SOLAR_CHARGE_MIN_VOLTAGE 7  /**< Sun is rising (morning detected) */
#define SOLAR_CHARGE_MAX_VOLTAGE 9  /**< Sun is shining (noon)  */
#define VOLT_MAX_BATT               4.2f

#define MAX_CONFIG_SETTING_ITEMS 50 /**< Parameter, that can be configured in Homie */

#define TEMPERATUR_TIMEOUT              3000    /**< 3 Seconds timeout for the temperatur sensors */
#define DS18B20_RESOLUTION              9       /**< 9bit temperature resolution -> 0.5°C steps */

/* @} */

#endif